Lenovo NetVista Hardware Maintenance Manual (HMM) for IBM NetVista 6029 system - Page 96

Flash recovery boot block jumper, Insert the upgrade diskette into the diskette drive.

Get Lenovo NetVista PDF manuals and user guides View all Lenovo NetVista manuals
Add to My Manuals
Save this manual to your list of manuals

Page 96 highlights

2. Insert the flash update diskette into drive A. 3. Power-on the computer. 4. When the Update Utility appears; select the country/keyboard, then press Enter. 5. If the computer serial number was previously recorded, the number is displayed with an option to update it. Press Y to update the serial number. 6. Type the 7-digit serial number of the computer you are servicing, then press Enter. 7. Follow the instructions on the screen to complete the flash (BIOS/VPD) update procedure. Flash recovery boot block jumper Attention: If an interruption occurs during a Flash/BIOS upgrade, the BIOS might be left in an unusable state. The Boot Block jumper enables you to restart the system and recover the BIOS. To perform a Flash/BIOS recovery using the recovery jumper, use the following procedure. 1. Power-off the computer and remove the cover. 2. Move the system board Virtual clear CMOS/BIOS recovery jumper to the ROM recovery position. Refer to "Identifying parts on the system board" on page 24 or the label inside the computer for more information. 3. Insert the upgrade diskette into the diskette drive. 4. Power-on the computer. The IBM Logo will appear. 5. When the Flash Update Utility appears, select the country/keyboard, then press Enter. 6. If the computer serial number was previously recorded, the number is displayed with an option to update it. Press Y to update the serial number. 7. Type the 7-digit serial number of the computer you are servicing, then press Enter. 8. Follow the instructions on the screen to complete the flash (BIOS/VPD) update procedure. 9. When you are instructed to reboot the computer, power-off the computer and move the recovery jumper to the normal position. Then replace the cover and power-on the computer. 90 Hardware Maintenance Manual

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
2.
Insert the flash update diskette into drive A.
3.
Power-on the computer.
4.
When the Update Utility appears; select the country/keyboard, then press
Enter
.
5.
If the computer serial number was previously recorded, the number is
displayed with an option to update it. Press
Y
to update the serial number.
6.
Type the 7-digit serial number of the computer you are servicing, then press
Enter
.
7.
Follow the instructions on the screen to complete the flash (BIOS/VPD) update
procedure.
Flash recovery boot block jumper
Attention:
If an interruption occurs during a Flash/BIOS upgrade, the BIOS might be left in an
unusable state. The Boot Block jumper enables you to restart the system and recover the
BIOS.
To perform a Flash/BIOS recovery using the recovery jumper, use the following
procedure.
1.
Power-off the computer and remove the cover.
2.
Move the system board Virtual clear CMOS/BIOS recovery jumper to the
ROM
recovery
position. Refer to
“
Identifying parts on the system board
”
on page 24
or the label inside the computer for more information.
3.
Insert the upgrade diskette into the diskette drive.
4.
Power-on the computer. The IBM Logo will appear.
5.
When the Flash Update Utility appears, select the country/keyboard, then press
Enter
.
6.
If the computer serial number was previously recorded, the number is
displayed with an option to update it. Press
Y
to update the serial number.
7.
Type the 7-digit serial number of the computer you are servicing, then press
Enter
.
8.
Follow the instructions on the screen to complete the flash (BIOS/VPD) update
procedure.
9.
When you are instructed to reboot the computer, power-off the computer and
move the recovery jumper to the
normal
position. Then replace the cover and
power-on the computer.
90
Hardware Maintenance Manual