Lenovo NetVista (English) User guide - Page 91

Selecting a startup device, Changing the startup sequence, Startup, Startup Sequence, Save Settings

Get Lenovo NetVista PDF manuals and user guides View all Lenovo NetVista manuals
Add to My Manuals
Save this manual to your list of manuals

Page 91 highlights

Selecting a startup device If your computer does not start up (boot) from a device such as the CD-ROM, diskette, or hard disk as expected, use one of the following procedures to select a startup device. Selecting a temporary startup device Use this procedure to startup from any boot device. Note: Not all CDs, hard disks, and diskettes are startable (bootable). 1. Turn off your computer. 2. Turn on your computer and look for the following prompt on the logo screen: (To interrupt normal startup, press Enter) Press Enter when you see the prompt. 3. When the Startup Interrupt Menu displays, press F12. 4. Select the desired startup device from the Startup Device menu and press Enter to begin. Note: Selecting a startup device from the Startup Device menu does not permanently change the startup sequence. Changing the startup sequence To view or change the primary or automatic power-on startup sequence, do the following: 1. Start the IBM Setup Utility program (see "Starting the IBM Setup Utility program" on page 77). 2. Select Startup. 3. Select Startup Sequence. See the information displayed on the right side of the screen. 4. Select the sequence of devices for the Primary Startup Sequence, the Automatic Startup Sequence, and the Error Startup Sequence. 5. Select Exit from the IBM Setup Utility menu and then Save Settings. If you have changed these settings and want to return to the default settings, select Load Default Settings on the Exit menu. Chapter 5. Using the IBM Setup Utility program 79

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
Selecting a startup device
If your computer does not start up (boot) from a device such as the CD-ROM,
diskette, or hard disk as expected, use one of the following procedures to select a
startup device.
Selecting a temporary startup device
Use this procedure to startup from any boot device.
Note:
Not all CDs, hard disks, and diskettes are startable (bootable).
1.
Turn off your computer.
2.
Turn on your computer and look for the following prompt on the logo screen:
(To interrupt normal startup, press Enter)
Press Enter when you see the prompt.
3.
When the Startup Interrupt Menu displays, press F12.
4.
Select the desired startup device from the Startup Device menu and press Enter
to begin.
Note:
Selecting a startup device from the Startup Device menu does not
permanently change the startup sequence.
Changing the startup sequence
To view or change the primary or automatic power-on startup sequence, do the
following:
1.
Start the IBM Setup Utility program (see
“
Starting the IBM Setup Utility
program
”
on page 77).
2.
Select
Startup
.
3.
Select
Startup Sequence
. See the information displayed on the right side of the
screen.
4.
Select the sequence of devices for the Primary Startup Sequence, the Automatic
Startup Sequence, and the Error Startup Sequence.
5.
Select
Exit
from the IBM Setup Utility menu and then
Save Settings
.
If you have changed these settings and want to return to the default settings, select
Load Default Settings
on the Exit menu.
Chapter 5. Using the IBM Setup Utility program
79