Lenovo ThinkCentre A58 Hardware Maintenance Manual - Page 64

FRU/Action, Power-off/on system and re-test

Get Lenovo ThinkCentre A58 PDF manuals and user guides View all Lenovo ThinkCentre A58 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 64 highlights

Diagnostic error code 001-025-XXX System Checksum Value error 001-026-XXX System FLASH data error 001-027-XXX System Configuration/Setup error 001-032-XXX System Device Controller failure 001-034-XXX System Device Buffer Allocation failure 001-035-XXX System Device Reset condition detected 001-036-XXX System Register error 001-038-XXX System Extension failure 001-039-XXX System DMI data structure error 001-040-XXX System IRQ failure 001-041-XXX System DMA failure 001-195-XXX System Test aborted by user 001-196-XXX System test halt, error threshold exceeded 001-197-XXX System test warning FRU/Action 1. Flash the system. See "Updating (flashing) BIOS from a disc" on page 134 2. System board 1. Flash the system. See "Updating (flashing) BIOS from a disc" on page 134 2. System board 1. Run Setup 2. Flash the system. See "Updating (flashing) BIOS from a disc" on page 134 3. System board System board 1. Reboot the system 2. Flash the system. See "Updating (flashing) BIOS from a disc" on page 134 3. Run memory test 4. System board System board System board 1. Adapter card 2. System board 1. Flash the system. See "Updating (flashing) BIOS from a disc" on page 134 2. System board 1. Power-off/on system and re-test 2. System board 1. Power-off/on system and re-test 2. System board Information only Re-start the test, if necessary 1. Press F3 to review the log file 2. Re-start the test to reset the log file 1. Make sure the component that is called out is connected and/or enabled. See Chapter 6, "Using the Setup Utility," on page 51 2. Re-run test 3. Replace the component that is called out in warning statement 4. Replace the component under test 58 Hardware Maintenance Manual

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
Diagnostic error code
FRU/Action
001-025-XXX
System Checksum Value error
1.
Flash the system. See “Updating
(flashing) BIOS from a disc” on page
134
2.
System board
001-026-XXX
System FLASH data error
1.
Flash the system. See “Updating
(flashing) BIOS from a disc” on page
134
2.
System board
001-027-XXX
System Configuration/Setup error
1.
Run Setup
2.
Flash the system. See “Updating
(flashing) BIOS from a disc” on page 134
3.
System board
001-032-XXX
System Device Controller failure
System board
001-034-XXX
System Device Buffer Allocation failure
1.
Reboot the system
2.
Flash the system. See “Updating
(flashing) BIOS from a disc” on page 134
3.
Run memory test
4.
System board
001-035-XXX
System Device Reset condition detected
System board
001-036-XXX
System Register error
System board
001-038-XXX
System Extension failure
1.
Adapter card
2.
System board
001-039-XXX
System DMI data structure error
1.
Flash the system. See “Updating
(flashing) BIOS from a disc” on page
134
2.
System board
001-040-XXX
System IRQ failure
1.
Power-off/on system and re-test
2.
System board
001-041-XXX
System DMA failure
1.
Power-off/on system and re-test
2.
System board
001-195-XXX
System Test aborted by user
Information only
Re-start the test, if necessary
001-196-XXX
System test halt, error threshold exceeded
1.
Press F3 to review the log file
2.
Re-start the test to reset the log file
001-197-XXX
System test warning
1.
Make sure the component that is called
out is connected and/or enabled. See
Chapter 6, “Using the Setup Utility,” on
page 51
2.
Re-run test
3.
Replace the component that is called out
in warning statement
4.
Replace the component under test
58
Hardware Maintenance Manual