Lenovo ThinkPad Edge 15 Hardware Maintenance Manual - Page 51

Error messages, Press F1 to enter BIOS Setup Utility. Press F9, - wireless card

Get Lenovo ThinkPad Edge 15 PDF manuals and user guides View all Lenovo ThinkPad Edge 15 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 51 highlights

Table 2. Numeric error codes (continued) Symptom or error (beeps, if any) 02F6 Software NMI failed (two short beeps) 02F7 Fail-safe timer NMI failed (two short beeps) 1802 Unauthorized network card is plugged in-Turn off and remove the miniPCI network card. (two short beeps) 1804 Unauthorized WAN card is plugged in-Power off and remove the WAN card. FRU or action, in sequence 1. DIMM. 2. System board. 1. DIMM. 2. System board. 1. Remove the Mini PCI network card. 2. System board. 1. Remove the wireless WAN card. 2. System board. Error messages Table 3. Error messages Symptom or error (beeps, if any) Bad CRC2. Enter BIOS Setup Utility, and load Setup defaults. (two short beeps) Fan error. (four short beeps, one long beep) DRAM is unplugged. (one short beep, pause, three short beeps, pause, three short beeps, pause, one short beep.) DRAM is not well plugged. (one short beep, pause, three short beeps, pause, three short beeps, pause, one short beep.) Operating system not found. System Configuration Data Read Error (two short beeps) FRU or action, in sequence Press F1 to enter BIOS Setup Utility. Press F9, and Enter to load the default setting. Then save the current setting by pressing F10, and restart the computer. 1. Fan. 2. Thermal grease. 3. System board. Memory card is not installed. Install memory card. Reinstall the memory card. 1. Check that the operating system has no failure and is installed correctly. 2. Enter BIOS Setup Utility and see whether the hard disk drive is properly identified. If you still see the same error message, check the boot sequence. 3. Reinstall the hard disk drive. 4. Reinstall the operating system. Press F1 to enter BIOS Setup Utility. Press F9, and Enter to load the default setting. Then save the current setting by pressing F10, and restart the computer. Chapter 4. Related service information 45

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
Table 2. Numeric error codes (continued)
Symptom or error (beeps, if any)
FRU or action, in sequence
02F6
Software NMI failed
(two short beeps)
1.
DIMM.
2. System board.
02F7
Fail-safe timer NMI failed
(two short beeps)
1.
DIMM.
2. System board.
1802
Unauthorized network card is plugged in—Turn off and
remove the miniPCI network card.
(two short beeps)
1.
Remove the Mini PCI network card.
2. System board.
1804
Unauthorized WAN card is plugged in—Power off and
remove the WAN card.
1.
Remove the wireless WAN card.
2. System board.
Error messages
Table 3. Error messages
Symptom or error (beeps, if any)
FRU or action, in sequence
Bad CRC2. Enter BIOS Setup Utility, and load Setup
defaults.
(two short beeps)
Press F1 to enter BIOS Setup Utility. Press F9, and
Enter to load the default setting. Then save the current
setting by pressing F10, and restart the computer.
Fan error.
(four short beeps, one long beep)
1.
Fan
.
2. Thermal grease.
3. System board.
DRAM is unplugged.
(one short beep, pause, three short beeps, pause, three
short beeps, pause, one short beep.)
Memory card is not installed. Install memory card.
DRAM is not well plugged.
(one short beep, pause, three short beeps, pause, three
short beeps, pause, one short beep.)
Reinstall the memory card.
Operating system not found.
1.
Check that the operating system has no failure
and is installed correctly.
2. Enter BIOS Setup Utility and see whether the hard
disk drive is properly identified. If you still see the
same error message, check the boot sequence.
3. Reinstall the hard disk drive.
4. Reinstall the operating system.
System Configuration Data Read Error
(two short beeps)
Press F1 to enter BIOS Setup Utility. Press F9, and
Enter to load the default setting. Then save the current
setting by pressing F10, and restart the computer.
Chapter 4
.
Related service information
45