Lenovo ThinkServer TS200 Hardware Maintenance Manual for TS200 - Page 176

Removing an optional ServeRAID-MR10i SAS/SATA controller, is part of a cluster solution - ibm

Get Lenovo ThinkServer TS200 PDF manuals and user guides View all Lenovo ThinkServer TS200 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 176 highlights

4. Install and lock the side cover (see "Installing the side cover" on page 143). 5. Reconnect the external cables and power cords; then, turn on the attached devices and turn on the server. Removing an optional ServeRAID-MR10i SAS/SATA controller To remove a ServeRAID-MR10i SAS/SATA adapter, complete the following steps: 1. Read the safety information beginning on page "Important Safety Information" on page 1. 2. Turn off the server and peripheral devices, and disconnect the power cords and all external cables. Remove the side cover (see "Removing the side cover" on page 142). 3. Rotate the rear adapter-retention bracket to the open (unlocked) position. 4. Disconnect any cables connected to the adapter. Attention: To avoid breaking the retaining clips or damaging the ServeRAID-MR10i adapter connector, open and close the clips gently. 5. Carefully grasp the end of the ServeRAID adapter and pull it out of the connector. 6. If you are instructed to return the adapter, follow all packaging instructions, and use any packaging materials for shipping that are supplied to you. Installing an optional ServeRAID-MR10i SAS/SATA controller The optional IBM ServeRAID-MR10i SAS/SATA controller can be installed in either PCI slot 1 or slot 2 on the system board. The ServeRAID-MR10i adapter is supported on hot-swap server models only. The IBM ServeRAID-MR10i SAS/SATA adapter enables integrated RAID levels 0, 1, 5, 6, and 10 support capability on hot-swap hard disk drives. For configuration information, see the documentation on the ServeRAID CD that comes with the adapter. To ensure that any of your ServeRAID 10i, 10is, or 10M adapters function properly on UEFI-based servers, make sure that the adapter firmware level is updated to at least 11.xx-XXX, and the supporting drivers. Attention: Some cluster solutions require specific code levels or coordinated code updates. If the device is part of a cluster solution, verify that the latest level of code is supported for the cluster solution before you update the code. To install a ServeRAID-MR10i adapter, complete the following steps: 1. Read the safety information beginning on page "Important Safety Information" on page 1. 2. Touch the static-protective package containing the ServeRAID-MR10i adapter to any unpainted metal surface on the server. Then, remove the ServeRAID-MR10i adapter from the package. 3. If the battery pack (battery carrier and battery) did not come installed on the ServeRAID adapter, install the battery pack. a. Align the battery carrier pins and the connector for the battery carrier with the pin holes and connector on the ServeRAID adapter; then, lower the battery carrier onto the ServeRAID adapter. 168 Hardware Maintenance Manual

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229
  • 230
  • 231
  • 232
  • 233
  • 234
  • 235
  • 236
  • 237
  • 238
  • 239
  • 240
  • 241
  • 242
  • 243
  • 244
  • 245
  • 246
  • 247
  • 248
  • 249
  • 250
  • 251
  • 252
  • 253
  • 254
  • 255
  • 256
  • 257
  • 258
  • 259
  • 260
  • 261
  • 262
  • 263
  • 264
  • 265
  • 266
  • 267
  • 268
  • 269
  • 270
  • 271
  • 272
  • 273
  • 274
  • 275
  • 276
  • 277
  • 278
  • 279
  • 280
  • 281
  • 282
  • 283
  • 284
  • 285
  • 286
  • 287
  • 288
  • 289
  • 290
  • 291
  • 292
  • 293
  • 294
  • 295
  • 296
  • 297
  • 298
4.
Install and lock the side cover (see “Installing the side cover” on page 143).
5.
Reconnect the external cables and power cords; then, turn on the attached devices and turn on the server.
Removing an optional ServeRAID-MR10i SAS/SATA controller
To remove a ServeRAID-MR10i SAS/SATA adapter, complete the following steps:
1.
Read the safety information beginning on page “Important Safety Information” on page 1.
2.
Turn off the server and peripheral devices, and disconnect the power cords and all external cables.
Remove the side cover (see “Removing the side cover” on page 142).
3.
Rotate the rear adapter-retention bracket to the open (unlocked) position.
4.
Disconnect any cables connected to the adapter.
Attention:
To avoid breaking the retaining clips or damaging the ServeRAID-MR10i adapter connector,
open and close the clips gently.
5.
Carefully grasp the end of the ServeRAID adapter and pull it out of the connector.
6.
If you are instructed to return the adapter, follow all packaging instructions, and use any packaging
materials for shipping that are supplied to you.
Installing an optional ServeRAID-MR10i SAS/SATA controller
The optional IBM ServeRAID-MR10i SAS/SATA controller can be installed in either PCI slot 1 or slot 2 on
the system board. The ServeRAID-MR10i adapter is supported on hot-swap server models only. The IBM
ServeRAID-MR10i SAS/SATA adapter enables integrated RAID levels 0, 1, 5, 6, and 10 support capability
on hot-swap hard disk drives. For configuration information, see the documentation on the ServeRAID CD
that comes with the adapter.
To ensure that any of your ServeRAID 10i, 10is, or 10M adapters function properly on UEFI-based servers,
make sure that the adapter firmware level is updated to at least 11.xx-XXX, and the supporting drivers.
Attention:
Some cluster solutions require specific code levels or coordinated code updates. If the device
is part of a cluster solution, verify that the latest level of code is supported for the cluster solution before
you update the code.
To install a ServeRAID-MR10i adapter, complete the following steps:
1.
Read the safety information beginning on page “Important Safety Information” on page 1.
2.
Touch the static-protective package containing the ServeRAID-MR10i adapter to any unpainted metal
surface on the server. Then, remove the ServeRAID-MR10i adapter from the package.
3.
If the battery pack (battery carrier and battery) did not come installed on the ServeRAID adapter, install
the battery pack.
a.
Align the battery carrier pins and the connector for the battery carrier with the pin holes and connector
on the ServeRAID adapter; then, lower the battery carrier onto the ServeRAID adapter.
168
Hardware Maintenance Manual