Lenovo ThinkStation D10 User Manual - Page 154

Replacing a hard disk drive, Install the new drive into the bracket, flex the bracket

Get Lenovo ThinkStation D10 PDF manuals and user guides View all Lenovo ThinkStation D10 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 154 highlights

Replacing a hard disk drive This section provides instructions on how to replace the hard disk drive. Note: When replacing a hard disk drive in a raid configured array, depending on which type of array is used, rebuilding the raid array might be required. If the array is redundant, make sure to connect the new drive to the same port from which the replaced drive was removed. To replace the hard disk drive: 1. Open the computer cover. See "Opening the cover" on page 130. 2. Disconnect the signal and power cables from the hard disk drive. 3. Pull the handle to remove the hard disk drive. 4. Remove the failing hard disk drive from the bracket by flexing the bracket. 5. Install the new drive into the bracket, flex the bracket, and align the pins 1 through 4 on the bracket with the holes in the hard disk drive. Do not touch the circuit board 5 on the bottom of the hard disk drive. 148 Hardware Maintenance Manual

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229
  • 230
  • 231
  • 232
  • 233
  • 234
  • 235
  • 236
  • 237
  • 238
  • 239
  • 240
  • 241
  • 242
  • 243
  • 244
  • 245
  • 246
  • 247
  • 248
Replacing a hard disk drive
This section provides instructions on how to replace the hard disk drive.
Note:
When replacing a hard disk drive in a raid configured array, depending on
which type of array is used, rebuilding the raid array might be required. If
the array is redundant, make sure to connect the new drive to the same port
from which the replaced drive was removed.
To replace the hard disk drive:
1.
Open the computer cover. See “Opening the cover” on page 130.
2.
Disconnect the signal and power cables from the hard disk drive.
3.
Pull the handle to remove the hard disk drive.
4.
Remove the failing hard disk drive from the bracket by flexing the bracket.
5.
Install the new drive into the bracket, flex the bracket, and align the pins
±1²
through
±4²
on the bracket with the holes in the hard disk drive. Do not touch
the circuit board
±5²
on the bottom of the hard disk drive.
148
Hardware Maintenance Manual