LevelOne GEL-2460 Manual - Page 14

Connecting Network Devices

Get LevelOne GEL-2460 PDF manuals and user guides View all LevelOne GEL-2460 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 14 highlights

Chapter 2 Hardware Installation Figure 2-1 Installing the Switch in a Rack 2.2.2 Installing the Switch on a Level Surface To install the Switch on a level surface (such as a desktop or shelf), follow these steps: Step 1 Place the Switch upside down on a sturdy, flat surface with a power outlet nearby. Step 2 Remove the adhesive backing from the supplied rubber feet. Attach the four rubber feet to the four round recessed areas on the bottom of the Switch. Step 3 Turn the Switch over to make it right side up on the flat surface. 2.3 Connecting Network Devices To connect network devices to the GEL-2460 Switch, follow these steps: Step 1 Make sure all devices you will connect to the Switch are powered off. Step 2 Connect a standard network cable from an available port on the Switch to a PC or other network device. Step 3 Repeat step 2 to connect rest network devices. Note All RJ-45 ports on the Switch support auto MDI/MDI-X feature. This means that you can use either a crossover cable or straight-through cable to connect a device to the Switch. http://www.level1.com Page 7

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
Chapter 2 Hardware Installation
Page 7
Figure 2-1 Installing the Switch in a Rack
2.2.2
Installing the Switch on a Level Surface
To install the Switch on a level surface (such as a desktop or shelf), follow these steps:
Step 1
Place the Switch upside down on a sturdy, flat surface with a power outlet
nearby.
Step 2
Remove the adhesive backing from the supplied rubber feet. Attach the four
rubber feet to the four round recessed areas on the bottom of the Switch.
Step 3
Turn the Switch over to make it right side up on the flat surface.
2.3
Connecting Network Devices
To connect network devices to the GEL-2460 Switch, follow these steps:
Step 1
Make sure all devices you will connect to the Switch are powered off.
Step 2
Connect a standard network cable from an available port on the Switch to a PC
or other network device.
Step 3
Repeat step 2 to connect rest network devices.
Note
All RJ-45 ports on the Switch support auto MDI/MDI-X feature. This means that you can
use either a crossover cable or straight-through cable to connect a device to the Switch.