LevelOne HVE-6601T Quick Install Guide - Page 4

HVE-6501R Receiver, LEDs , button and Group ID setting, Transmitter & Receiver IP Address

Get LevelOne HVE-6601T PDF manuals and user guides View all LevelOne HVE-6601T manuals
Add to My Manuals
Save this manual to your list of manuals

Page 4 highlights

 HVE-6501R Receiver 1. DC5V/PoE: Connect to the supplied AC adapter and plug into an electrical outlet. Or via 802.3af PoE PSE to GIGA LAN port. 2. GIGA LAN: Connect directly to a Transmitter or to a Gigabit IGMP Ethernet Switch using CAT5e/6 cable. 3. HDMI OUT: Connect to an HDMI display device with an HDMI M-M cable. Use an HDMI --> DVI adapter if the display is DVI. LEDs , button and Group ID setting 1. POWER LED Blinking: power on and the unit is booting up. 2. POWER LED On: power on and the unit is active. 3. LINK LED Off: LAN is not connected. 4. LINK LED On: LAN is connected. 5. DATA LED Blinking: The Receiver is connecting with Transmitter, or the HDMI source is removed. 6. DATA LED On: All the connections are working. 7. PB 1 : Change Link/Unlink; Firmware Upgrade Mode and Reset to default* using this button. Please to see the Button Descriptions. 8. PB 2 : change between Video Mode / Graphic Mode ; Anti-Dither ; Update EDID* using this button. Please to see the Push Button Descriptions. 9. GROUP ID: The Receiver's default GROUP ID is "0000". Set the same group ID as Transmitter.  Transmitter & Receiver IP Address The default setting is for "auto ip" mode and uses the 169.254.xxx.xxx private IP domain range. The IP of target TX/RX board is resolved by its hostname using DNS protocol. The RX's HDMI GUI will display the RX's IP address and the connected TX's IP address. You can see the RX's HDMI GUI by connecting it with power adapter and HDMI monitor only, without LAN cable. Page4

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
Page4
HVE-6501R Receiver
1.
DC5V/PoE:
Connect to the supplied AC adapter and plug into an
electrical outlet. Or via 802.3af PoE PSE to GIGA LAN port.
2.
GIGA LAN:
Connect directly to a Transmitter or to a Gigabit IGMP
Ethernet Switch using CAT5e/6 cable.
3.
HDMI OUT:
Connect to an HDMI display device with an HDMI M-M cable.
Use an HDMI --> DVI adapter if the display is DVI.
LEDs , button and Group ID setting
1.
POWER LED Blinking:
power on and the unit is booting up.
2.
POWER LED On:
power on and the unit is active.
3.
LINK LED Off:
LAN is not connected.
4.
LINK LED On:
LAN is connected.
5.
DATA LED Blinking:
The Receiver is connecting with Transmitter, or the
HDMI source is removed.
6.
DATA LED On:
All the connections are working.
7.
PB 1
: Change Link/Unlink; Firmware Upgrade Mode and Reset to
default* using this button. Please to see the
Button Descriptions.
8.
PB 2 :
change between Video Mode / Graphic Mode ; Anti-Dither ; Update
EDID* using this button. Please to see the
Push Button Descriptions.
9.
GROUP ID:
The Receiv
er’s default GROUP ID is “0000”
. Set the same
group ID as Transmitter.
Transmitter & Receiver IP Address
The default setting is
for “auto
ip” mode and uses the 169.254.xxx.xxx private
IP domain range. The IP of target TX/RX board is resolved by its hostname
using DNS protocol. The RX’s HDMI GUI will display the RX’s IP address and
the connected TX’s IP address. You can see the RX’s
HDMI GUI by
connecting it with power adapter and HDMI monitor only, without LAN cable.