LevelOne WAP-6202 User Manual - Page 10

In-Ceiling Access Point

Get LevelOne WAP-6202 PDF manuals and user guides View all LevelOne WAP-6202 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 10 highlights

In-Ceiling Access Point 2.5 Panel Descriptions The in-ceiling wireless access point supports IEEE 802.3af PoE. A system status LED is located at the front panel, a LAN port is located at the bottom panel, and a reset button is located at the side panel. 1）LED LED System Status LED Description The LED flashes twice per second when the system is operating properly, and it will flash slower if the system is under heavy load. Table 2-1 Description of LED - In-ceiling AP 2） Port Port LAN Description Gigabit Ethernet RJ45 port, auto MDI/MDI-X Table 2-2 Description of Ports - In-ceiling AP 3） Reset Button If you forget the administrator password, you can use the Reset button to reset the Device to factory default settings. The operation is as follows: With the Device powered on, press and hold the Reset button for more than 5 seconds, and then release the button. The Device will restart with factory default settings. Note：The reset operation will clear all custom settings on the Device, so do it with caution. 2.6 Preparing for Installation 1） Make sure that there is proper heat dissipation and adequate ventilation around the Device. 2） Position the Device out of direct sunlight and away from sources of heat and ignition. 3） Position the Device away from sources of electrical noise, such as high power radiotransmitters, radar stations, and so on. 9

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
9
In-Ceiling Access Point
2.5
Panel Descriptions
The in-ceiling wireless access point supports IEEE 802.3af PoE. A system status LED is located at
the front panel, a LAN port is located at the bottom panel, and a reset button is located at the side
panel.
1
）
LED
LED
Description
System Status LED
The LED flashes twice per second when the system is operating
properly, and it will flash slower if the system is under heavy
load.
Table
2-1 Description of LED
–
In-ceiling AP
2
）
Port
Port
Description
LAN
Gigabit Ethernet RJ45 port, auto MDI/MDI-X
Table
2-2
Description of Ports
–
In-ceiling AP
3
）
Reset
Button
If you forget the administrator password, you can use the
Reset
button to reset the Device to
factory default settings. The operation is as follows:
With the Device powered on, press and hold
the
Reset
button for more than 5 seconds, and then release the button. The Device will restart with
factory default settings.
Note
：
The reset operation will clear all custom settings on the Device, so do it with caution.
2.6
Preparing for Installation
1
）
Make sure that there is proper heat dissipation and adequate ventilation around the Device.
2
）
Position the Device out of direct sunlight and away from sources of heat and ignition.
3
）
Position the Device away from sources of electrical noise, such as high power
radiotransmitters, radar stations, and so on.