LevelOne WAP-6202 User Manual - Page 11

Items Required for Installation, Typical Deployment Scenarios

Get LevelOne WAP-6202 PDF manuals and user guides View all LevelOne WAP-6202 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 11 highlights

2.7 Items Required for Installation The following items are required for installation: 1. Broadband Internet connection 2. Tools and equipment • Wireless LAN controller or normal router • PC with an Ethernet card and TCP/IP installed • Power outlet • (Optional) PoE PSE (Power Sourcing Equipment) device like PoE switch • Ethernet cables • Phillips screwdriver.。 Installing the Device Before you install the Device, make sure your Internet connection is working properly. In addition, it is recommended that you configure the Device before you deploy it in the network. Follow these steps to install the Device: 1. Use the supplied power adapter to connect the Device to a power outlet. 2. Connect your computer to the Device either via an Ethernet cable or wirelessly, and then login to the Web UI to configure the Device. 3. After you configure the Device, unplug the power adapter, and the Ethernet cable, if used. 4. Mount the Device on a ceiling or wall. 5. If needed, use an Ethernet cable to connect other network device (like PoE switch, WLAN controller) to the LAN port of the Device. 6. Power the Device by using the supplied power adapter, a PoE adapter, or a PoE switch. 7. Connect client devices: Connect each computer or other device in your network to the Device wirelessly. 2.8 Typical Deployment Scenarios The WAP-6111/H、WAP-6112/H、WAP-6201、WAP-6202 can operate in either Fit AP or Fat AP mode. Figure 0-2 depicts a typical Fit access point deployment, and Figure 0- depicts a typical Fat access point deployment. As shown in Figure 0-, two access points act as Fit APs, a WAC-1000 / WAC-1001 controller acts as the gateway. The access points are managed by the WAC-1000 / WAC-1001, and clients access the network through the access points. 10

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
10
2.7
Items Required for Installation
The following items are required for installation:
1.
Broadband Internet connection
2.
Tools and equipment
•
Wireless LAN controller or normal router
•
PC with an Ethernet card and TCP/IP installed
•
Power outlet
•
(Optional) PoE PSE (Power Sourcing Equipment) device like PoE switch
•
Ethernet cables
•
Phillips screwdriver.
。
Installing the Device
Before you install the Device, make sure your Internet connection is working
properly. In
addition, it is recommended that you configure the Device before you deploy it in the network.
Follow these steps to install the Device:
1. Use the supplied power adapter to connect the Device to a power outlet.
2. Connect your computer to the Device either via an Ethernet cable or wirelessly, and then
login to the Web UI to configure the Device.
3. After you configure the Device, unplug the power adapter, and the Ethernet cable, if
used.
4. Mount the Device on a ceiling or wall.
5. If needed, use an Ethernet cable to connect other network device (like PoE switch,
WLAN controller) to the LAN port of the Device.
6. Power the Device by using the supplied power adapter, a PoE adapter, or a PoE switch.
7. Connect client devices: Connect each computer or other device in your network to the
Device wirelessly.
2.8
Typical Deployment Scenarios
The WAP-6111/H
、
WAP-6112/H
、
WAP-6201
、
WAP-6202 can operate in either Fit
AP or Fat AP mode. Figure 0-2 depicts a typical Fit access point deployment, and
Figure 0- depicts a typical Fat access point deployment.
As shown in Figure 0-, two access points act as Fit APs, a WAC-1000 / WAC-1001
controller acts as the gateway. The access points are managed by the WAC-1000 /
WAC-1001, and clients access the network through the access points.