LevelOne WGR-6012 Manual - Page 80

please go to this to input the information ISP is assigned. - factory reset

Get LevelOne WGR-6012 PDF manuals and user guides View all LevelOne WGR-6012 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 80 highlights

light? A: First, please check Status Led. If the device is normal, the led will blink per second. If not, please check How blinking Status led shows. There are many abnormal symptoms as below: Status Led is bright or dark in work: The system hanged up .Suggest powering off and on the router. But this symptom often occurs, please reset to default or upgrade latest FW to try again. Status led flashes irregularly: Maybe the root cause is Flash ROM and please press reset Button to reset to default or try to use Recovery mode.(Refer to Q3 and Q4) Status flashes very fast while powering on: Maybe the router is the recovery mode and please refer to Q4. 3.How to reset to factory default? A: Press Wireless on /off and WPS button simultaneously about 5 sec Status will start flashing about 5 times, remove the finger. The RESTORE process is completed. 4.Why can I not connect Internet even though the cables are plugged in Wan port and LAN port and the LEDs are blink. In addition, Status led is also normal and I can configure web management? A: Make sure that the network cable from DSL or Cable modem is plugged in WAN port of Router and that the network cable from LAN port of router is plugged in Ethernet adapter. Then, please check which wan type you use. If you are not sure, please call the ISP. Then please go to this page to input the information ISP is assigned. 80

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
80
light?
A:
First, please check Status Led. If the device is normal, the led will blink per second.
If not, please check How blinking Status led shows.
There are many abnormal symptoms as below:
Status Led is bright or dark in work:
The system hanged up .Suggest powering off and on
the router. But this symptom often occurs, please reset to default or upgrade latest FW to try
again.
Status led flashes irregularly:
Maybe the root cause is Flash ROM and please press reset
Button to reset to default or try to use Recovery mode.(Refer to Q3 and Q4)
Status flashes very fast while powering on:
Maybe the router is the recovery mode and
please refer to Q4.
3.How to reset to factory default?
A:
Press Wireless on /off and WPS button simultaneously about 5 sec
Status will start flashing about 5 times, remove the finger. The RESTORE process is completed.
4.Why can I not connect Internet even though the cables are plugged in Wan port and LAN
port and the LEDs are blink. In addition, Status led is also normal and I can configure web
management?
A: Make sure that the network cable from DSL or Cable modem is plugged in WAN port of
Router and that the
network cable from LAN port of router is plugged in Ethernet adapter.
Then, please check which wan type you use. If you are not sure, please call the ISP. Then
please go to this page to input the information ISP is assigned.