Lexmark C750 User's Guide - Page 213
Restore Held Jobs. Go/Stop?, Restoring Held Job xxx/yyy 97 - 900 error code
View all Lexmark C750 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 213 highlights
numerical values 7 messages in . Go? 100 Alignment 73 100-199 Service 101 1565 Emul Error Load Emul Option 102 2 Paper Jam 102 30 Toner Cart Missing 103 30 ITU Missing 102 31 Defective Cartridge 103 33 Calibration Error 103 34 Short Paper 104 35 Res Save Off Deficient Memory 104 37 Insufficient Collation Area 105 37 Insufficient Defrag Memory 105 37 Insufficient Memory 106 38 Memory Full 106 39 Complex Page 107 4 Unsupported Firmware Card 107 51 Defective Flash 107 52 Flash Full 108 53 Unformatted Flash 108 54 Network Software Error 109 54 Par ENA Connection Lost 109 54 Serial Option Error 108 54 Standard Serial Error 108 54 Std Network Software Error 109 54 Std Par ENA Connection Lost 109 56 Parallel Port Disabled 110 56 Serial Port Disabled 109 56 Standard Serial Disabled 109 56 Standard USB Port Disabled 110 56 Std Parallel Port Disabled 110 56 USB Port Disabled 110 58 Too Many Disks Installed 111 58 Too Many Flash Options 111 58 Too Many Trays Attached 111 59 Incompatible 112 61 Defective Disk 112 62 Disk Full 112 63 Unformatted Disk 113 64 Disk Not Supported 113 64 Unsupported Disk Format 113 80 Fuser Maintenance 114 81 Engine Code CRC Failure 114 81 ITU Maintenance 114 82 Oiler Nearly Exhausted 115 82 Replace Oiler 115 82 Waste Toner Bottle Full 115 82 Waste Toner Bottle Missing 116 87 Fuser Missing 116 88 Toner Low 116 88 Waste Bottle Nearly Full 117 900-999 Service 117 Activating Menu Changes 73 Bin Full 73 Busy 74 Calibrate Load Paper 74 Calibrating Tray 74 Cancelling Fax 75 Cancelling Job 75 Change 75 Change Invalid Refill 76 Check Connection 76 Clearing Job Accounting Stat 76 Close Door 77 Close Finisher Door 77 Close Tray X Door 77 Copying 77 Defragmenting 78 Delete All Jobs 78 Deleting Jobs 78 Disabling Menus 79 Disk Corrupted. Reformat? 79 Disk Recovery x/5 yyy% 79 Enabling Menus 80 Engine Warming 80 Enter PIN =___ 80 Fax 81 Flushing Buffer 81 Formatting Disk 81 Formatting Disk yyy% 81 Formatting Flash 82 Held Jobs may be lost 82 Hole Punch Waste Full 82 Incorrect Media 83 Infrared 83 Insert Staple Cartridge 83 Insert Tray 83 Install or Cancel Job 84 Invalid Engine Code 84 Invalid Network Code 84 Invalid Standard Network Code 84 ITU/Fuser Maint 85 Load Manual 85 Load Staples 85 Load Tray 86 LocalTalk 86 Menus Disabled 86 Network 87 Network , 87 Network Card Busy 87 No DRAM Installed 87 No Jobs Found. Retry? 88 Not Ready 88 Ovrflow Bin Full 88 Parallel 88 Performing Self Test 89 Power Saver 89 Print Jobs on Disk 90 Printer Calibrating 89 Printing Alignment Page 90 Printing Directory List 90 Printing Font List 91 Printing Job Accounting Stat 91 Printing Menu Settings 91 Prog Engine Code 92 Prog System Code 92 Program Flash 92 Programming Disk 92 Programming Error P 93 Queuing and Deleting Jobs 93 Queuing Jobs 93 Ready 94 Ready Hex 94 Reattach 94 Remove Paper 95 Resetting Active Bin 95 Resetting Fuser Cnt Value 95 Resetting the Printer 95 Restore Held Jobs. Go/Stop? 96 Restoring Factory Defaults 96 Restoring Held Job xxx/yyy 97 Restoring Held Jobs 97 Serial 97 Setup Required 98 Staples Low 98 Std Bin Full 98 Supplies 99 Tray Empty 99 Tray Low 99 Tray Missing 100 Tray Not Calibrated 100 USB 101 Waiting 101 Multipage Border (Finishing Menu) 136 Multipage Order (Finishing Menu) 137 211