Lexmark E360DN Service Manual - Page 46

A recoverable MVRAM Cyclic Redundancy Check error, Replace the LVPS/HVPS. See

Get Lexmark E360DN - Hv Taa/gov Compliant PDF manuals and user guides
UPC - 734646084475
View all Lexmark E360DN manuals
Add to My Manuals
Save this manual to your list of manuals

Page 46 highlights

4513-420, -430 Error Description Action 936.01 No lock detected at normal motor start 936.02 No lock detected at motor start for motor ID 936.03 No halls detected at motor start 936.04 Failed to stop within timeout 936.05 Stall detected during speed control 937.00 Main transport motor lost lock 937.01 Main transport motor lost lock, detected by engine control 937.02 Overspeed detected during position control 937.03 Overspeed detected during speed control Power supply service errors 940.00 LVPS service error 940.01 Line frequency outside allowed range of 45Hz-64Hz 940.02 Line frequency below 43Hz 940.03 No zero cross detected on belt fuser model Replace the main motor gear drive. See "Main motor service check" on page 2-26 Replace the main motor gear drive. See "Main motor service check" on page 2-26 Replace the LVPS/HVPS. See "LVPS/HVPS service check" on page 2-25. Controller board and operator panel service errors 948.xx 949.xx Failed engine board Replace the controller board. See "Controller board service check" on page 2-22. 950.xx Mismatch between EEPROM and mirror memory Note: A new controller board or operator panel has been installed, and has not been properly prepared for this use. Install a new note. Do not install both the controller board and the operator panel at the same time without a POR in between. Install a new controller bored or operator panel. See "Controller board service check" on page 2-22 or "Operator panel service check" on page 2-27. 951.xx Error with secure NVRAM on the controller board Replace the controller board. See "Controller board service check" on page 2-22. 952.xx A recoverable MVRAM Cyclic Redundancy Check error Performing POR will clear this error. occurred. 953.xx NVRAM chip failure with mirror Replace the operator panel. See "Operator panel service check" on page 2-27. 954.xx 955.xx NVRAM chip failure with system part. The code ROM or NAND flash failed the Cyclic Redundancy Check or the NAND experienced an uncorrectible multi-bit failure. Replace the controller board. See "Controller board service check" on page 2-22. 956.00 RIP card failure: processor failure 956.01 Processor overtemp 957.xx RIP card failure: ASIC failure 958.xx Printer has performed more than 100 "shift and reflash" operations as a result of ECC bit corrections 2-18 Lexmark™ E360d, E360dn

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
2-18
Lexmark™ E360d, E360dn
4513-420, -430
936.01
No lock detected at normal motor start
Replace the main motor gear drive. See
“Main
motor service check” on page 2-26
936.02
No lock detected at motor start for motor ID
936.03
No halls detected at motor start
936.04
Failed to stop within timeout
936.05
Stall detected during speed control
937.00
Main transport motor lost lock
Replace the main motor gear drive. See
“Main
motor service check” on page 2-26
937.01
Main transport motor lost lock, detected by engine
control
937.02
Overspeed detected during position control
937.03
Overspeed detected during speed control
Power supply service errors
940.00
LVPS service error
Replace the LVPS/HVPS. See
“LVPS/HVPS
service check” on page 2-25
.
940.01
Line frequency outside allowed range of 45Hz-64Hz
940.02
Line frequency below 43Hz
940.03
No zero cross detected on belt fuser model
Controller board and operator panel service errors
948.xx
Failed engine board
Replace the controller board. See
“Controller
board service check” on page 2-22
.
949.xx
950.xx
Mismatch between EEPROM and mirror memory
Note:
A new controller board or operator panel has been
installed, and has not been properly prepared for this
use. Install a new note. Do not install both the controller
board and the operator panel at the same time without a
POR in between.
Install a new controller bored or operator panel.
See
“Controller board service check” on
page 2-22
or
“Operator panel service check”
on page 2-27
.
951.xx
Error with secure NVRAM on the controller board
Replace the controller board. See
“Controller
board service check” on page 2-22
.
952.xx
A recoverable MVRAM Cyclic Redundancy Check error
occurred.
Performing POR will clear this error.
953.xx
NVRAM chip failure with mirror
Replace the operator panel. See
“Operator
panel service check” on page 2-27
.
954.xx
NVRAM chip failure with system part.
Replace the controller board. See
“Controller
board service check” on page 2-22
.
955.xx
The code ROM or NAND flash failed the Cyclic
Redundancy Check or the NAND experienced an
uncorrectible multi-bit failure.
956.00
RIP card failure: processor failure
956.01
Processor overtemp
957.xx
RIP card failure: ASIC failure
958.xx
Printer has performed more than 100 “shift and reflash”
operations as a result of ECC bit corrections
Error
Description
Action