Lexmark T634 Setup Guide - Page 62

Verifying the IPsettings, Configuring for PullPrinting, ping 192.168.0.11

Get Lexmark T634 PDF manuals and user guides View all Lexmark T634 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 62 highlights

8 Repeat step 6 to set the IP Netmask. 9 Press Menu until you see Set IP Gateway, and then press Select. 10 Repeat step 6 to set the IP Gateway. 11 When you are finished, press Go to return the printer to the Ready state. 12 Go to "Verifying the IP settings" on page 57. Verifying the IP settings Note: To reach a command prompt on Windows computers, click Start Programs Command prompt (or Accessories Command prompt if using Windows 2000). 1 Print another network setup page. Look under the "TCP/IP" heading and make sure the IP address, netmask, and gateway are what you expected. See "Printing a network setup page" on page 54 if you need help. 2 Ping the printer and verify that it responds. For example, at a command prompt on a network computer, type ping followed by the new printer IP address (for example): ping 192.168.0.11 If the printer is active on the network, you receive a reply. Configuring for Pull Printing If your printer has an optional ImageQuick firmware card installed, you can configure for Pull Printing once an IP address has been assigned to the printer. For detailed configuration instructions, refer to the CD that shipped with the ImageQuick firmware card. Configure for TCP/IP 57

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
57
Configure for TCP/IP
8
Repeat step 6 to set the IP Netmask.
9
Press
Menu
until you see Set IP Gateway, and then press
Select
.
10
Repeat step 6 to set the IP Gateway.
11
When you are finished, press
Go
to return the printer to the
Ready state.
12
Go to “Verifying the IP settings” on page 57.
Verifying the
IP settings
1
Print another network setup page. Look under the “TCP/IP”
heading and make sure the IP address, netmask, and gateway
are what you expected.
See “Printing a network setup page” on page 54 if you need
help.
Note:
To reach a command
prompt on Windows
computers, click Start
Programs
Command
prompt (or Accessories
Command prompt if using
Windows 2000).
2
Ping the printer and verify that it responds. For example, at a
command prompt on a network computer, type
ping
followed
by the new printer IP address (for example):
ping 192.168.0.11
If the printer is active on the network, you receive a reply.
Configuring for
Pull Printing
If your printer has an optional ImageQuick firmware card installed, you
can configure for Pull Printing once an IP address has been assigned
to the printer.
For detailed configuration instructions, refer to the CD that shipped
with the ImageQuick firmware card.