LiftMaster 3800 3800 Manual - Page 17

Caution, Warning - remote

Page 17 highlights

ADJUSTMENT STEP 1 Program the Travel Limits Travel limits regulate the points at which the door will stop when moving up or down. Follow the steps below to set the limits. Figure 1 Indicator Light Black Button Purple Button To program the travel limits: Adjust the position of the door by using the black and purple buttons. Black moves the door UP (open) and purple moves the door DOWN (close). 1. Setting the UP position: Press and hold the black button until the yellow indicator light starts flashing slowly then release. 2. Push and hold the black button until the door reaches the desired UP (open) position (Figure 2). NOTE: Check to be sure the door opens high enough for your vehicle. 3. Push the remote control or door control (Figure 3). This sets the UP (open) limit and begins closing the door. NOTE: Excessive movement of the motor unit will cause premature wear. See Troubleshooting section. 4. Immediately when the door begins to move down, press and release either the black or purple button. This will stop the door. 5. Setting the DOWN position: Push and hold the purple button until the door reaches the desired DOWN (closed) position (Figure 4). 6. Once the door is closed, if there appears to have too much pressure on the door, you may toggle the door back and forth using the black and purple buttons to reach the desired closed position. 7. Push the remote control or the door control (Figure 3). This sets the DOWN (close) limit and should bring the door to the open position. • If the opener is not stopping exactly where you would like it, repeat steps 1 through 8 and program the limits again. • When the unit stops in both the desired up (open) and down (close) positions, proceed to Adjustment Steps 2, Setting the Force. WARNING Without a properly installed safety reversal system, persons CAUTION (particularly small children) could be SERIOUSLY INJURED or KILLED by a closing garage door. • NEVER learn forces or limits when door is binding or sticking. Repair door first. • Incorrect adjustment of garage door travel limits will interfere with proper operation of safety reversal system. • After ANY adjustments are made, the safety reversal system MUST be tested. Door MUST reverse on contact with 1-1/2" high (3.8 cm) object (or 2x4 laid flat) on floor. WARNING CAUTION To prevent damage to vehicles, be sure fully open door provides adequate clearance. Figure 2 Push and hold until the door is at desired UP position BLACK PURPLE Figure 3 Figure 4 BLACK PURPLE or LOCK LIGHT Push either button to stop door at desired DOWN position 17

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32

17
To prevent damage to vehicles, be sure fully open door
provides adequate clearance.
CAUTION
BLACK
PURPLE
P
u
sh and hold
u
ntil the door
is at desired
UP
position
Fi
g
ure 2
Figure 3
P
u
sh either
bu
tton to stop
door at desired
DOWN
position
BLACK
PURPLE
Fi
g
ure 4
or
LOCK
LIGHT
Without a properly installed safety reversal system, persons
(particularly small children) could be SERIOUSLY INJURED
or KILLED by a closing garage door.
• NEVER learn forces or limits when door is binding or
sticking. Repair door first.
• Incorrect adjustment of garage door travel limits will
interfere with proper operation of safety reversal system.
• After ANY adjustments are made, the safety reversal
system MUST be tested. Door MUST reverse on contact
with 1-1/2" high (3.8 cm) object (or 2x4 laid flat) on floor.
WARNING
ADJUSTMENT STEP 1
Program the Travel Limits
Travel limits regulate the points at which the door
will stop when moving up or down. Follow the steps
below to set the limits.
To program the travel limits:
Adjust the position of the door by using the black and
purple buttons. Black moves the door UP (open) and
purple moves the door DOWN (close).
1.
Setting the UP position:
Press and hold the black
button until the yellow indicator light starts flashing
slowly then release.
2. Push and hold the black button until the door reaches
the desired UP (open) position (Figure 2).
NOTE:
Check to be sure the door opens high enough for
your vehicle.
3. Push the remote control or door control (Figure 3).
This sets the UP (open) limit and begins closing the
door.
NOTE:
Excessive movement of the motor unit will cause
premature wear. See Troubleshooting section.
4. Immediately when the door begins to move down,
press and release either the black or purple button.
This will stop the door.
5.
Setting the DOWN position:
Push and hold the
purple button until the door reaches the desired
DOWN (closed) position (Figure 4).
6. Once the door is closed, if there appears to have too
much pressure on the door, you may toggle the door
back and forth using the black and purple buttons to
reach the desired closed position.
7. Push the remote control or the door control (Figure 3).
This sets the DOWN (close) limit and should bring the
door to the open position.
• If the opener is not stopping exactly where you would
like it, repeat steps 1 through 8 and program the
limits again
.
• When the unit stops in both the desired up (open)
and down (close) positions, proceed to
Adjustment Steps 2, Setting the Force.
Purple
Button
Indicator
Light
Black
Button
Figure 1