LiftMaster CSL24UL Installation Manual - Page 34

Wiring accessories to the expansion board, Single Button Control, SBC 2

Get LiftMaster CSL24UL PDF manuals and user guides View all LiftMaster CSL24UL manuals
Add to My Manuals
Save this manual to your list of manuals

Page 34 highlights

EXPANSION BOARD Wiring accessories to the expansion board Refer to the chart below and the corresponding image for a description of the expansion board inputs. 1 Wireless edge Connection for wireless edge receiver 2 Entrapment Protection Device EYES ONLY Input: Open or Close Direction Photoelectric Sensors, Close: reverses fully, Open: reverses 4 Inputs (4 terminals total), Open or seconds Close Direction based on switch setting next to inputs EYES/EDGE Input(s): Open or Close Direction Photoelectric Sensors, Infra-red detector wired or Edge Sensor, reverses 4 seconds 3 Single Button Control, SBC (2 terminals) Gate command sequence - Open, Stop, Close, Stop, ... Soft Open ,Soft Close, Soft Stop (maintained switch does not override external safeties and does not reset alarm condition) 4 Open Input (& common) (3-Button Open command - opens a closed gate. Control Station, 4 terminals total) Soft open (maintained switch does not override external safeties and does not reset alarm condition) If maintained, pauses Timer-to-Close at OPEN limit. Opens a closing gate and holds open an open gate. 5 Close Input (& common) (3-Button Close command - closes an open gate. Control Station, 4 terminals total) Soft close (maintained switch does not override external safeties and does not reset alarm condition). 6 Stop Input (& common) (3-PB station, 4 terminals total) Stop command - stops a moving gate. Hard stop (maintained switch overrides Open and Close commands and resets alarm condition) If maintained, pauses Timer-to-Close at OPEN limit. Overrides an Open or Close command. 7 Exit Loop Input (2 terminals) Loop wire connection for plug-in loop detector when loop is inside secured area near gate. Open command - opens a closed gate. Soft open (maintained switch does not override external safeties and does not reset alarm condition) If maintained, pauses Timer-to-Close at OPEN limit. Opens a closing gate and holds open an open gate. 8 Shadow Loop Input (2 terminals) Loop wire connection for plug-in loop detector when loop is positioned under the gate. l Holds open gate at open limit l Disregarded during gate motion l Pauses Timer-to-Close at Open Limit 9 Interrupt Loop Input (2 terminals) Loop wire connection for plug-in loop detector when loop is along the side of the gate. l Holds open gate at open limit l Stops and reverses a closing gate l Pauses Timer-to-Close at Open Limit 34

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
34
Wiring accessories to the expansion board
Refer to the chart below and the corresponding image for a description of the expansion board inputs.
1
Wireless edge
Connection for wireless edge receiver
2
Entrapment Protection Device
Inputs (4 terminals total), Open or
Close Direction based on switch
setting next to inputs
EYES ONLY Input: Open or Close Direction Photoelectric Sensors, Close: reverses fully, Open: reverses 4
seconds
EYES/EDGE Input(s): Open or Close Direction Photoelectric Sensors, Infra-red detector wired or Edge
Sensor, reverses 4 seconds
3
Single Button Control, SBC (2
terminals)
Gate command sequence - Open, Stop, Close, Stop, ... Soft Open ,Soft Close, Soft Stop (maintained
switch does not override external safeties and does not reset alarm condition)
4
Open Input (& common) (3-Button
Control Station, 4 terminals total)
Open command - opens a closed gate.
Soft open (maintained switch does not override external safeties and does not reset alarm condition) If
maintained, pauses Timer-to-Close at OPEN limit.
Opens a closing gate and holds open an open gate.
5
Close Input (& common) (3-Button
Control Station, 4 terminals total)
Close command - closes an open gate.
Soft close (maintained switch does not override external safeties and does not reset alarm condition).
6
Stop Input (& common) (3-PB
station, 4 terminals total)
Stop command - stops a moving gate.
Hard stop (maintained switch overrides Open and Close commands and resets alarm condition) If
maintained, pauses Timer-to-Close at OPEN limit.
Overrides an Open or Close command.
7
Exit Loop Input (2 terminals)
Loop wire connection for plug-in loop detector when loop is inside secured area near gate.
Open command - opens a closed gate.
Soft open (maintained switch does not override external safeties and does not reset alarm condition) If
maintained, pauses Timer-to-Close at OPEN limit.
Opens a closing gate and holds open an open gate.
8
Shadow Loop Input (2 terminals)
Loop wire connection for plug-in loop detector when loop is positioned under the gate.
l
Holds open gate at open limit
l
Disregarded during gate motion
l
Pauses Timer-to-Close at Open Limit
9
Interrupt Loop Input (2 terminals)
Loop wire connection for plug-in loop detector when loop is along the side of the gate.
l
Holds open gate at open limit
l
Stops and reverses a closing gate
l
Pauses Timer-to-Close at Open Limit
EXPANSION BOARD