LiftMaster PPLX Installation Guide - Page 7

Operation, Troubleshooting

Get LiftMaster PPLX PDF manuals and user guides View all LiftMaster PPLX manuals
Add to My Manuals
Save this manual to your list of manuals

Page 7 highlights

OPERATION USING WIEGAND ACCESS CARDS & TRANSMITTERS WITH THE READER To use the reader, simply hold your Credential Device near the reader. The reader generates a short range RF field, which causes the Credential Device to send a unique ID Number back to the reader. REMOTE OPEN (REQUEST TO EXIT) INPUT When the Remote Open input is activated, the relay will activate. When the Remote Open input is deactivated, the relay will return to the inactive state after the latch timer times out. A Green LED and a beep indicate that access is granted. If the Credential Device ID Number is stored in memory, the latch relay is activated. A Green light and a beep indicate that access is granted. If the device ID Number is not stored in memory, the relay remains inactive, and a Red light and beep indicate that access is denied. Otherwise, the LED is normally off. THE READER IS COMPATIBLE WITH THE FOLLOWING LIFTMASTER® WIEGAND CREDENTIALS: • PassportTM: PPCSC (Card), CPTK13PH & CPTK33PH (Transmitter) • Sentex®: SNACPH3x & SNACPHIS03x (Card), SNACPKH3x (Transmitter) • LiftMaster® Q: CACC & CACISO (Card) USING THE READER AS A WIEGAND OUTPUT READER The reader can be connected to a multi-door access control system (such as the LiftMaster® Q2010 Site Control System) using the Wiegand output. When any LiftMaster® Credential Device is presented to the reader, whether or not it has been programmed into the reader, the appropriate Credential Device ID will be sent out via the white and green wires. Refer to "Configure the Reader Input" to control the LED. TROUBLESHOOTING LED IS FLASHING RED AND GREEN: a. No facility code has been programmed into the reader. Present a card. You will hear a beep, then the LED will stop flashing in 10 seconds. b. LED is still flashing. Check the card type, it must be 34 bit Passporr, 30 bit Sentex®, or 26 bit industry standard Credential Device. CANNOT ENTER PROGRAMMING MODE: a. LED is flashing red and green. No facility code has been programmed into the reader. Present a card. You will hear a beep, then the LED will stop flashing in 10 seconds. b. LED is solid green The remote open input is turned on (black & brown wires are shorted). Remove the short. c. Default Password (12345) has been changed. Refer to Password in the Advanced Programming section. CARDS DO NOT UNLOCK THE DOOR: Card reader beeps, LED flashes Red once. The cards have not been programmed into the reader. Refer to Add User in the Basic Programming section. 7

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
OPERATION
USING
WIEGAND
ACCESS
CARDS
&
TRANSMITTERS
WITH
THE
READER
To
use
the
reader,
simply
hold
your
Credential
Device
near
the
reader.
The
reader
generates
a
short
range
RF
field,
which
causes
the
Credential
Device
to
send
a
unique
ID
Number
back
to
the
reader.
If
the
Credential
Device
ID
Number
is
stored
in
memory,
the
latch
relay
is
activated.
A
Green
light
and
a
beep
indicate
that
access
is
granted.
If
the
device
ID
Number
is
not
stored
in
memory,
the
relay
remains
inactive,
and
a
Red
light
and
beep
indicate
that
access
is
denied.
Otherwise,
the
LED
is
normally
off.
THE
READER
IS
COMPATIBLE
WITH
THE
FOLLOWING
LIFTMASTER®
WIEGAND
CREDENTIALS:
•
PassportTM:
PPCSC
(Card),
CPTK13PH
&
CPTK33PH
(Transmitter)
•
Sentex®:
SNACPH3x
&
SNACPHIS03x
(Card),
SNACPKH3x
(Transmitter)
•
LiftMaster®
Q:
CACC
&
CACISO
(Card)
TROUBLESHOOTING
REMOTE
OPEN
(REQUEST
TO
EXIT)
INPUT
When
the
Remote
Open
input
is
activated,
the
relay
will
activate.
When
the
Remote
Open
input
is
deactivated,
the
relay
will
return
to
the
inactive
state
after
the
latch
timer
times
out.
A
Green
LED
and
a
beep
indicate
that
access
is
granted.
USING
THE
READER
AS
A
WIEGAND
OUTPUT
READER
The
reader
can
be
connected
to
a
multi
-door
access
control
system
(such
as
the
LiftMaster®
Q2010
Site
Control
System)
using
the
Wiegand
output.
When
any
LiftMaster®
Credential
Device
is
presented
to
the
reader,
whether
or
not
it
has
been
programmed
into
the
reader,
the
appropriate
Credential
Device
ID
will
be
sent
out
via
the
white
and
green
wires.
Refer
to
"Configure
the
Reader
Input"
to
control
the
LED.
LED
IS
FLASHING
RED
AND
GREEN:
a.
No
facility
code
has
been
programmed
into
the
reader.
Present
a
card.
You
will
hear
a
beep,
then
the
LED
will
stop
flashing
in
10
seconds.
b.
LED
is
still
flashing.
Check
the
card
type,
it
must
be
34
bit
Passporr,
30
bit
Sentex®,
or
26
bit
industry
standard
Credential
Device.
CANNOT
ENTER
PROGRAMMING
MODE:
a.
LED
is
flashing
red
and
green.
No
facility
code
has
been
programmed
into
the
reader.
Present
a
card.
You
will
hear
a
beep,
then
the
LED
will
stop
flashing
in
10
seconds.
b.
LED
is
solid
green
The
remote
open
input
is
turned
on
(black
&
brown
wires
are
shorted).
Remove
the
short.
c.
Default
Password
(12345)
has
been
changed.
Refer
to
Password
in
the
Advanced
Programming
section.
CARDS
DO
NOT
UNLOCK
THE
DOOR:
Card
reader
beeps,
LED
flashes
Red
once.
The
cards
have
not
been
programmed
into
the
reader.
Refer
to
Add
User
in
the
Basic
Programming
section.
7