Linksys WCM300 Cisco Cable Wideband Solution Design and Implementation Guide, - Page 66

Monitoring Wideband Channels, show interface wideband-cable

Get Linksys WCM300 - Channel Bonded Cable Modem PDF manuals and user guides View all Linksys WCM300 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 66 highlights

Monitoring Wideband Components Chapter 5 Monitoring and Troubleshooting Wideband Components Bit Rate: 1300 Mbps 50 micron-multimode fiber supported length: 550 m 62.5 micron-multimode fiber supported length: 270 m Upper bit rate limit: not specified Lower bit rate limit: not specified Date code (yy/mm/dd): 05/02/23 Vendor name: CISCO-AGILENT Vendor OUI: 12499 Vendor Part Number (PN): QFBR-5766LP Vendor Rev: Vendor SN (SN): AGS090855CE Options implemented: LOS Signal TX Fault Signal TX Disable Signal Enhanced options implemented: none Diagnostic monitoring implemented: none Idprom contents (hex): 0x00: 03 04 07 00 00 00 01 00 00 00 00 01 0D 00 00 00 0x10: 37 1B 00 00 43 49 53 43 4F 2D 41 47 49 4C 45 4E 0x20: 54 20 20 20 00 00 30 D3 51 46 42 52 2D 35 37 36 0x30: 36 4C 50 20 20 20 20 20 20 20 20 20 03 52 00 B5 0x40: 00 1A 00 00 41 47 53 30 39 30 38 35 35 43 45 20 0x50: 20 20 20 20 30 35 30 32 32 33 20 20 00 00 00 C4 0x60: 00 00 06 C9 F0 FA 7C 01 B3 C8 41 6B 39 04 FC 85 0x70: BB 20 9E 00 00 00 00 00 00 00 00 00 B4 94 52 CC 0x80: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF 0x90: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF State: Initalized Phased Initialization Phase Reached: 4 Phase Exit Code: 0 Phase Read Offset: 0 ... Monitoring Wideband Channels The following commands are useful for monitoring wideband channels: • show interface wideband-cable • show hw-module bay show interface wideband-cable To display information about a wideband-cable interface (wideband channel), use the show interface wideband-cable command. Wideband channels are similar to cable interfaces and information about them is also displayed with the show ip interfaces and show interfaces commands. Cisco Cable Wideband Solution Design and Implementation Guide, Release 1.0 5-6 OL-10705-02

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
5-6
Cisco Cable Wideband Solution Design and Implementation Guide, Release 1.0
OL-10705-02
Chapter 5
Monitoring and Troubleshooting Wideband Components
Monitoring Wideband Components
Bit Rate: 1300 Mbps
50 micron-multimode fiber supported length: 550 m
62.5 micron-multimode fiber supported length: 270 m
Upper bit rate limit: not specified
Lower bit rate limit: not specified
Date code (yy/mm/dd): 05/02/23
Vendor name: CISCO-AGILENT
Vendor OUI: 12499
Vendor Part Number (PN): QFBR-5766LP
Vendor Rev:
Vendor SN (SN): AGS090855CE
Options implemented:
LOS Signal
TX Fault Signal
TX Disable Signal
Enhanced options implemented: none
Diagnostic monitoring implemented: none
Idprom contents (hex):
0x00:
03 04 07 00 00 00 01 00 00 00 00 01 0D 00 00 00
0x10:
37 1B 00 00 43 49 53 43 4F 2D 41 47 49 4C 45 4E
0x20:
54 20 20 20 00 00 30 D3 51 46 42 52 2D 35 37 36
0x30:
36 4C 50 20 20 20 20 20 20 20 20 20 03 52 00 B5
0x40:
00 1A 00 00 41 47 53 30 39 30 38 35 35 43 45 20
0x50:
20 20 20 20 30 35 30 32 32 33 20 20 00 00 00 C4
0x60:
00 00 06 C9 F0 FA 7C 01 B3 C8 41 6B 39 04 FC 85
0x70:
BB 20 9E 00 00 00 00 00 00 00 00 00 B4 94 52 CC
0x80:
FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x90:
FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
State: Initalized
Phased Initialization
Phase Reached: 4
Phase Exit Code: 0
Phase Read Offset: 0
...
Monitoring Wideband Channels
The following commands are useful for monitoring wideband channels:
•
show interface wideband-cable
•
show hw-module bay
show interface wideband-cable
To display information about a wideband-cable interface (wideband channel), use the
show interface
wideband-cable
command. Wideband channels are similar to cable interfaces and information about
them is also displayed with the
show ip interfaces
and
show interfaces
commands.