Linksys WRE54G Cisco WAP54GP Wireless-G Access Point with Power Over Ethernet - Page 17

Navigating the Utility, Setup, Wireless - manual

Get Linksys WRE54G - Wireless-G Range Expander Repeater PDF manuals and user guides
UPC - 745883559046
View all Linksys WRE54G manuals
Add to My Manuals
Save this manual to your list of manuals

Page 17 highlights

Wireless-G Access Point with Power Over Ethernet (192.168.1.245). Or if there is DHCP server connected to the switch, configure it to assign the IP address in the192.168.1.0/24 subnet. Your PC will get an IP address in the subnet through the DHCP. 3. Although not recommended, you can connect your PC wirelessly to the Access Point when the DHCP server is connected on the LAN side. It is not recommended, because you can easily lose your connection through configuration changes. Launch your web browser, such as Internet Explorer or Mozilla Firefox and enter the Access Point's default IP address, 192.168.1.245, in the Address field. Press the Enter key. Enter admin in the User Name field. The first time you open the Web-based Utility, use the default password, admin. (You can set a new password from the Administration - Management tab.) Then click the OK button. After setting up the Access Point to use DHCP or manually configure a new IP address, move your Access Point to the desired network. You will have to use the new IP address the next time you access the Web-based Utility. Navigating the Utility The Web-based Utility consists of the following five main tabs: Setup, Wireless, AP Mode, Administration, and Status. Additional screens (sub tabs) will be available from most of the main tabs. The following briefly describes the main & sub tabs of the Utility. Setup Enter the Host Name and IP Address settings on this screen. Wireless You will use the Wireless tabs to enter a variety of wireless settings for the Access Point. • Basic Wireless Settings. Choose the wireless network mode (e.g. wireless-G), Virtual Local Area Network (VLAN) settings, SSIDs, and transmit rates on this screen. • Wireless Security. Use this screen to configure the Access Point's security settings. • Wireless Network Access. Use this screen to populate your Access List to permit or block certain MAC address access to your wireless network. • Advanced Wireless Settings. Use this screen to configure the Access Point's more advanced wireless settings (e.g. Wireless Isolation, Output Power, etc.). Chapter 5: Setting Up the Wireless-G Access Point with Power Over Ethernet 11 Navigating the Utility

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
11
Chapter 5: Setting Up the Wireless-G Access Point with Power Over Ethernet
Navigating the Utility
Wireless-G Access Point with Power Over Ethernet
(192.168.1.245). Or if there is DHCP server connected to the switch, configure it to assign the IP address in
the192.168.1.0/24 subnet. Your PC will get an IP address in the subnet through the DHCP.
3.
Although not recommended, you can connect your PC wirelessly to the Access Point when the DHCP server is
connected on the LAN side. It is not recommended, because you can easily lose your connection through
configuration changes.
Launch your web browser, such as Internet Explorer or Mozilla Firefox and enter the Access Point’s default IP
address,
192.168.1.245
, in the
Address
field. Press the
Enter
key.
Enter
admin
in the
User Name
field. The first time you open the Web-based Utility, use the default password,
admin
. (You can set a new password from the Administration - Management tab.) Then click the
OK
button.
After setting up the Access Point to use DHCP or manually configure a new IP address, move your Access Point to
the desired network. You will have to use the new IP address the next time you access the Web-based Utility.
Navigating the Utility
The Web-based Utility consists of the following five main tabs: Setup, Wireless, AP Mode, Administration, and
Status. Additional screens (sub tabs) will be available from most of the main tabs.
The following briefly describes the main & sub tabs of the Utility.
Setup
Enter the Host Name and IP Address settings on this screen.
Wireless
You will use the Wireless tabs to enter a variety of wireless settings for the Access Point.
•
Basic Wireless Settings
. Choose the wireless network mode (e.g. wireless-G), Virtual Local Area Network
(VLAN) settings, SSIDs, and transmit rates on this screen.
•
Wireless Security
. Use this screen to configure the Access Point’s security settings.
•
Wireless Network Access
. Use this screen to populate your Access List to permit or block certain MAC
address access to your wireless network.
•
Advanced Wireless Settings
. Use this screen to configure the Access Point’s more advanced wireless settings
(e.g. Wireless Isolation, Output Power, etc.).