Linksys WRE54G Cisco WAP54GP Wireless-G Access Point with Power Over Ethernet - Page 18

AP Mode, Administration, Status, System Performance - firmware upgrade

Get Linksys WRE54G - Wireless-G Range Expander Repeater PDF manuals and user guides
UPC - 745883559046
View all Linksys WRE54G manuals
Add to My Manuals
Save this manual to your list of manuals

Page 18 highlights

Wireless-G Access Point with Power Over Ethernet AP Mode Use this screen to configure the Access Point operation mode with WDS (Wireless Distribution System). Administration You will use the Administration tabs to manage the Access Point. • Management. This screen allows you to customize the password and Simple Network Management Protocol (SNMP) settings. • Log. Configure the Log settings for the Access Point on this screen. • Factory Default. Use this screen to reset the Access Point to its factory default settings. • Firmware Upgrade. Upgrade the Access Point's firmware on this screen. • Reboot. Use this screen to reboot the Access Point. • Config Management. You can back up the configuration file for the Access Point, as well as save the backup configuration file to the Access Point. Status You will be able to view status information for your local network, wireless networks, and network performance. • Local Network. This screen displays system information, including software & hardware version, MAC address, and IP address on the LAN side of the Access Point. • Wireless. This screen will display current information on the Access Point and its wireless networks. • System Performance. This screen will display current information on the Access Point and its data transmissions. snmp: the standard network management protocol on the Internet. firmware: the software image that runs on a CPU inside a networking device. Chapter 5: Setting Up the Wireless-G Access Point with Power Over Ethernet 12 Navigating the Utility

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
12
Chapter 5: Setting Up the Wireless-G Access Point with Power Over Ethernet
Navigating the Utility
Wireless-G Access Point with Power Over Ethernet
AP Mode
Use this screen to configure the Access Point operation mode with WDS (Wireless Distribution System).
Administration
You will use the Administration tabs to manage the Access Point.
•
Management
. This screen allows you to customize the password and Simple Network Management Protocol
(SNMP) settings.
•
Log
. Configure the Log settings for the Access Point on this screen.
•
Factory Default
. Use this screen to reset the Access Point to its factory default settings.
•
Firmware Upgrade
. Upgrade the Access Point’s firmware on this screen.
•
Reboot
. Use this screen to reboot the Access Point.
•
Config Management
. You can back up the configuration file for the Access Point, as well as save the backup
configuration file to the Access Point.
Status
You will be able to view status information for your local network, wireless networks, and network performance.
•
Local Network
. This screen displays system information, including software & hardware version, MAC
address, and IP address on the LAN side of the Access Point.
•
Wireless
. This screen will display current information on the Access Point and its wireless networks.
•
System Performance
. This screen will display current information on the Access Point and its data
transmissions.
firmware:
the software image that runs on a
CPU inside a networking device.
snmp:
the standard network management protocol
on the Internet.