Lowrance HDS-7 Gen2 Touch Installation Manual - Page 15

Flush mounting - hds touch manual

Get Lowrance HDS-7 Gen2 Touch PDF manuals and user guides View all Lowrance HDS-7 Gen2 Touch manuals
Add to My Manuals
Save this manual to your list of manuals

Page 15 highlights

Flush mounting Check the template for scaling accuracy, using a tape measure or ruler against the ruler printed on the template. 95.3 mm (7.50") MOUNTING SCREW SIZE IS #6 TAPPING SCREW CL 110.2 mm (3.75") 99.5 mm (3.92") 95.3 mm (7.50") PRODUCSTUNOUCTOLVINEER 190.5 mm (7.50") 199.0 mm (7.83") 220.4 mm (8.68") Check dimensions before cutting 12" CL Cut away excess paper, and tape down the template. Check it is correctly aligned to a vertical or horizontal reference. Do not use a bubble level as vessel may be listing! Adjust where required. Drill all marked pilot holes, then using an appropriate saw, cut through the template and mounting surface, along the dotted line bordering the shaded center of the template. Remove the bezel from the display, using a fingernail or small flat screwdriver, starting at the edges that are closest to the card reader door. Check the fit of the display, and use a file to remove any remaining obstructions. If water-tightness is required, apply a thin, continuous bead of sealant to the back of the display prior to final installation. Sealant should be of a 'neutral cure' type to prevent damage to the plastics. Secure the display with the supplied screws. Once screws are fully tightened, ensure there is complete contact with the mounting surface. Lastly, fit the bezel with the card reader door open; insert the outermost tabs on the bezel in to the slots on the display, then gently press down the bezel above and below the card reader door till it clicks in to place. Display Installation | HDS Gen2 Touch Installation Manual | 13

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
| 13
Display Installation |
HDS Gen2 Touch Installation Manual
Flush mounting
Check the template for scaling accuracy, using a tape measure or
ruler against the ruler printed on the template.
L
C
L
C
Check dimensions before cutting
Cut away excess paper, and tape down the template. Check it is
correctly aligned to a vertical or horizontal reference. Do not use a
bubble level as vessel may be listing! Adjust where required.
Drill all marked pilot holes, then using an appropriate saw, cut
through the template and mounting surface, along the dotted line
bordering the shaded center of the template.
Remove the bezel from the display, using a fingernail or small flat
screwdriver, starting at the edges that are closest to the card reader
door.
Check the fit of the display, and use a file to remove any remaining
obstructions. If water-tightness is required, apply a thin, continuous
bead of sealant to the back of the display prior to final installation.
Sealant should be of a ‘neutral cure’ type to prevent damage to
the plastics. Secure the display with the supplied screws. Once
screws are fully tightened, ensure there is complete contact with
the mounting surface. Lastly, fit the bezel with the card reader door
open; insert the outermost tabs on the bezel in to the slots on the
display, then gently press down the bezel above and below the card
reader door till it clicks in to place.