MSI K8T MASTER2-FAR User Guide - Page 52

LDT & PCI Bus Control

Get MSI K8T MASTER2-FAR - Motherboard - ATX PDF manuals and user guides
UPC - 816909004427
View all MSI K8T MASTER2-FAR manuals
Add to My Manuals
Save this manual to your list of manuals

Page 52 highlights

MS-9617 ATX Workstation Board MTRR Mapping Mode This setting controls the MTRR mapping mode. To install the W inXP64, this setting should be set to [Continuous]. Setting options: [Continuous], [Discrete]. DRAM ECC Feature Control If all memory in the system supports ECC, enabling this will initial scrub dram and enable system requests to dram to be checked and/or corrected. Options: [Enabled], [Disabled]. ECC MCE Enable This setting enables/disables the ECC MCE function. Options: [Enabled], [Disabled]. Chip-Kill Mode Enable This item allows you to enable/disable Chip-Kill ECC on Nodes with all x4 ECC capable dimms. Options: [Enabled], [Disabled]. ECC Redirection Enable Scrubber to correct errors detected in DRAM during normal CPU requests (foreground scrubbing). Options: [Enabled], [Disabled]. LDT & PCI Bus Control Press and the following sub-menu appears: Upstream / Downstream LDT Bus Width These two item control the utilized widths of the HyperTransport link. Setting options: [8 bit], [16 bit]. LDT Bus Frequency This item specifies the maximum operating frequency of the link's transmitter clock. Setting options: [Auto], [800 MHz], [600 MHz], [400 MHz], [200 MHz]. 3-12

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
3-12
MS-9617 ATX Workstation Board
MTRR Mapping Mode
This setting controls the MTRR mapping mode. To install the WinXP64, this
setting should be set to [Continuous]. Setting options: [Continuous], [Discrete].
DRAM ECC Feature Control
If all memory in the system supports ECC, enabling this will initial scrub dram and
enable system requests to dram to be checked and/or corrected. Options:
[Enabled], [Disabled].
ECC MCE Enable
This setting enables/disables the ECC MCE function. Options: [Enabled],
[Disabled].
Chip-Kill Mode Enable
This item allows you to enable/disable Chip-Kill ECC on Nodes with all x4 ECC
capable dimms. Options: [Enabled], [Disabled].
ECC Redirection
Enable Scrubber to correct errors detected in DRAM during normal CPU re-
quests (foreground scrubbing). Options: [Enabled], [Disabled].
LDT & PCI Bus Control
Press <Enter> and the following sub-menu appears:
Upstream / Downstream LDT Bus Width
These two item control the utilized widths of the HyperTransport link. Setting
options: [8 bit], [16 bit].
LDT Bus Frequency
This item specifies the maximum operating frequency of the link's transmitter
clock. Setting options: [Auto], [800 MHz], [600 MHz], [400 MHz], [200 MHz].