MSI P965 NEO-F User Guide - Page 50

Parallel Port IRQ

Get MSI P965 NEO-F - Motherboard - ATX PDF manuals and user guides
UPC - 816909035490
View all MSI P965 NEO-F manuals
Add to My Manuals
Save this manual to your list of manuals

Page 50 highlights

MS-7235 Mainboard SATA#1 Configuration This item allows you to configurare IDE device mode. [Compatible] If Compatible selected, Legacy IDE Channels will only use IRQ14 and IRQ15. [Enhanced] If Enhanced selected, you could use the other IRQs (except IRQ14 and IRQ15). I/O Devices Press to enter the sub-menu: Onboard Floppy Controller Select [Enabled] if your system has a floppy disk controller (FDC) installed on the system board and you wish to use it. If you install add-on FDC or the system has no floppy drive, select [Disabled] in this field. COM Port 1 / 2 This item allows you to select Serial Port1 base addresses. COM Port 2 Mode This setting allows you to specify the operation mode for serial port 2. [Normal] RS-232C Serial Port [IrDA] IrDA-compliant Serial Infrared Port [ASKIR] Amplitude Shift Keyed Infrared Port Parallel Port There is a built-in parallel port on the on-board Super I/O chipset that provides Standard, ECP, and EPP features. Parallel Port M ode [Normal] Standard Parallel Port [EPP] Enhanced Parallel Port [ECP] Extended Capability Port [ECP+ EPP] Extended Capability Port + Enhanced Parallel Port To operate the onboard parallel port as Standard Parallel Port only, choose [Normal]. To operate the onboard parallel port in the EPP mode simultaneously, choose [EPP]. By choosing [ECP], the onboard parallel port will operate in ECP mode only. Choos- ing [ECP + EPP] will allow the onboard parallel port to support both the ECP and EPP modes simultaneously. Parallel Port IRQ This item allows you to set parallel port IRQ. 3-12

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
MS-7235 Mainboard
3-12
SATA#1 Configuration
This item allows you to configurare IDE device mode.
[Compatible]
If Compatible selected, Legacy IDE Channels will only use IRQ14
and IRQ15.
[Enhanced]
If Enhanced selected, you could use the other IRQs (except
IRQ14 and IRQ15).
I/O Devices
Press <Enter> to enter the sub-menu:
Onboard Floppy Controller
Select [Enabled] if your system has a floppy disk controller (FDC) installed on the
system board and you wish to use it. If you install add-on FDC or the system has
no floppy drive, select [Disabled] in this field.
COM Port 1 / 2
This item allows you to select Serial Port1 base addresses.
COM Port 2 Mode
This setting allows you to specify the operation mode for serial port 2.
[Normal]
RS-232C Serial Port
[IrDA]
IrDA-compliant Serial Infrared Port
[ASKIR]
Amplitude Shift Keyed Infrared Port
Parallel Port
There is a built-in parallel port on the on-board Super I/O chipset that provides
Standard, ECP, and EPP features.
Parallel Port Mode
[Normal]
Standard Parallel Port
[EPP]
Enhanced Parallel Port
[ECP]
Extended Capability Port
[ECP + EPP]
Extended Capability Port + Enhanced Parallel Port
To operate the onboard parallel port as Standard Parallel Port only, choose [Normal].
To operate the onboard parallel port in the EPP mode simultaneously, choose [EPP].
By choosing [ECP], the onboard parallel port will operate in ECP mode only. Choos-
ing [ECP + EPP] will allow the onboard parallel port to support both the ECP and EPP
modes simultaneously.
Parallel Port IRQ
This item allows you to set parallel port IRQ.