Mackie MS1202-VLZ Owner's Manual - Page 10
Ms1202-vlz Patchbay Description - mixer
View all Mackie MS1202-VLZ manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 10 highlights
MS1202-VLZ PATCHBAY DESCRIPTION At the risk of stating the obvious, this is where you plug everything in: microphones, line-level instruments and effects, headphones, and the ultimate destination for your sound: a tape recorder, PA system, etc. MIC INPUTS (Channels 1-4) We use phantom-powered, balanced microphone inputs just like the big studio mega-consoles, for exactly the same reason: This kind of circuit is excellent at rejecting hum and noise. You can plug in almost any kind of mic that has a standard XLR-type male mic connector. To learn how signals are routed from these inputs: . If you wire your own, connect them like this: SHIELD 2 HOT COLD 3 1 SHIELD 1 COLD 3 2 HOT 1 3 2 SHIELD COLD HOT Pin 1 = Ground or shield Pin 2 = Positive (+ or hot) Pin 3 = Negative (- or cold) Professional ribbon, dynamic, and condenser mics will all sound excellent through these inputs. The MS1202-VLZ's mic inputs will handle any kind of mic level you can toss at them, without overloading. Be sure to perform the Level-Setting Procedure: . PHANTOM POWER Most modern professional condenser mics are equipped for Phantom Power, which lets the mixer send low-current DC voltage to the mic's electronics through the same wires that carry audio. (Semipro condenser mics often have batteries to accomplish the same thing.) "Phantom" owes its name to an ability to be "unseen" by dynamic mics (Shure SM57/SM58, for instance), which don't need external power and aren't affected by it anyway. The MS1202-VLZ's phantom power is globally controlled by the PHANTOM switch on the rear panel . (This means the phantom power for channels 1-4 is turned on and off together.) Never plug single-ended (unbalanced) microphones or instruments into the MIC input jacks if the PHANTOM power is on. Do not plug instrument outputs into the MIC input jacks with PHANTOM power on unless you know for certain it is safe to do so. LINE INPUTS (Channels 1-4) These four line inputs share circuitry (but not phantom power) with the mic preamps, and can be driven by balanced or unbalanced sources at almost any level. You can use these inputs for virtually any signal you'll come across, from instrument levels as low as -30dB to operating levels of -10dBV to +4dBu, since there is 30dB more gain available than on channels 5-12. To learn how signals are routed from these inputs: . MIC 1 MIC 2 MIC 3 MIC 4 LEFT/MONO RIGHT 1 ALL BAL/UNBAL 1 LEFT RIGHT 2 L 2 R BAL/UNBAL L R BAL OR UNBAL BAL OR UNBAL BAL OR UNBAL BAL OR STEREO AUX RETURNS AUX SEND UNBAL MONO MONO LINE IN 1 LOW CUT 75 Hz 18dB/OCT MIC GA-I1N0 U LINE IN 2 LOW CUT 75 Hz 18dB/OCT MIC GA-I1N0 U LINE IN 3 LOW CUT 75 Hz 18dB/OCT MIC GA-I1N0 U LINE IN 4 LOW CUT 75 Hz 18dB/OCT MIC GA-I1N0 U L BAL OR UNBAL R L BAL OR UNBAL R 10 60 +10dB -40dB TRIM 10 60 +10dB -40dB TRIM 10 60 +10dB -40dB TRIM 10 60 +10dB -40dB TRIM LINE IN 5-6 LINE IN 7-8 TAPE TAPE INPUT OUTPUT MONO MAIN OUTS MONO L L BAL OR UNBAL BAL OR UNBAL R R LINE IN 9-10 LINE IN 11-12 10