Makita XSH08Z XSH08 Instruction Manual - Page 15

Optional Accessories

Get Makita XSH08Z PDF manuals and user guides View all Makita XSH08Z manuals
Add to My Manuals
Save this manual to your list of manuals

Page 15 highlights

Adjusting 0°-cut or 45°-cut accuracy This adjustment has been made at the factory. But if it is off, you can adjust it as the following procedure. 1. Loosen the clamping screws on the front and rear of the tool so that the bevel angle can be changed. Set the stopper to 0° - 45° bevel angle position if you are going to adjust 45°-cut accuracy. 1 Adjusting the parallelism CAUTION: Keep the parallelism accurate. Otherwise the circular saw blade may bite into the guide rail and the damaged guide rail may cause an injury. This adjustment has been made at the factory. But if it is off, you can adjust it as the following procedure. 1. Set the tool to the maximum cutting depth. 2. Make sure all levers and screws are tightened. 3. Loosen the screws shown in the figure. 4. While opening the lower guard, move the rear of the base so that the distance A and B becomes equal. 1 A ► 1 . Stopper 2. Make the base perpendicular or 45° to the circular saw blade using a triangular rule by turning the adjusting screw with a hex wrench. You can also use a square rule to adjust 0° angle. 1 1 B 2 1 ► 1 . Screw 2. Base 5. Tighten the screws and make a test cut to check the parallelism. OPTIONAL ACCESSORIES ► 1 . Triangular rule 2 1 ► 1 . Adjusting screw for 0° angle 2. Adjusting screw for 45° angle 3. Tighten the clamping screws and then make a test cut to check if desired angle is obtained. CAUTION: These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. Only use accessory or attachment for its stated purpose. If you need any assistance for more details regarding these accessories, ask your local Makita Service Center. • Circular saw blade • Rip fence (Guide rule) • Hook • Guide rail • Bevel guide • Clamp • Sheet • Rubber sheet • Position sheet • Dust nozzle • Hex wrench • Makita genuine battery and charger NOTE: Some items in the list may be included in the tool package as standard accessories. They may differ from country to country. 15 ENGLISH

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
15
ENGLISH
Adjusting 0°-cut or 45°-cut accuracy
This adjustment has been made at the factory. But if it is
off, you can adjust it as the following procedure.
1.
Loosen the clamping screws on the front and rear
of the tool so that the bevel angle can be changed. Set
the stopper to 0° - 45° bevel angle position if you are
going to adjust 45°-cut accuracy.
1
►
1.
Stopper
2.
Make the base perpendicular or 45° to the circular
saw blade using a triangular rule by turning the adjust
-
ing screw with a hex wrench. You can also use a square
rule to adjust 0° angle.
1
1
►
1.
Triangular rule
2
1
►
1.
Adjusting screw for 0° angle
2.
Adjusting screw
for 45° angle
3.
Tighten the clamping screws and then make a test
cut to check if desired angle is obtained.
Adjusting the parallelism
CAUTION:
Keep the parallelism accurate.
Otherwise the circular saw blade may bite into the guide
rail and the damaged guide rail may cause an injury.
This adjustment has been made at the factory. But if it is
off, you can adjust it as the following procedure.
1.
Set the tool to the maximum cutting depth.
2.
Make sure all levers and screws are tightened.
3.
Loosen the screws shown in the figure.
4.
While opening the lower guard, move the rear of
the base so that the distance A and B becomes equal.
1
B
A
2
1
►
1.
Screw
2.
Base
5.
Tighten the screws and make a test cut to check
the parallelism.
OPTIONAL ACCESSORIES
CAUTION:
These accessories or attachments
are recommended for use with your Makita tool spec-
ified in this manual.
The use of any other accessories
or attachments might present a risk of injury to persons.
Only use accessory or attachment for its stated purpose.
If you need any assistance for more details regarding
these accessories, ask your local Makita Service Center.
•
Circular saw blade
•
Rip fence (Guide rule)
•
Hook
•
Guide rail
•
Bevel guide
•
Clamp
•
Sheet
•
Rubber sheet
•
Position sheet
•
Dust nozzle
•
Hex wrench
•
Makita genuine battery and charger
NOTE:
Some items in the list may be included in the
tool package as standard accessories. They may
differ from country to country.