Marantz CC4003 CC4003 User Manual - English - Page 4

NAMES AND FUNCTIONS BASIC CONNECTIONS BASIC OPERATIONS ADVANCED CONNECTIONS ENGLISH FEATURES BEFORE USING SUPPORTS MP3 AND WMA FILE PLAYBACK MP3 and WMA files that have been recorded onto CD-R or CD-RW discs can be played back on this CD player. (See page 14) WHILE PLAYING A DISC, FOUR OTHER DISCS CAN BE CHANGED DIRECT DISC ACCESS BUTTON Direct Disc Access button is equipped both on the front panel of the unit and on the remote controller for one-touch disc change to any of the 5 discs in the unit. VARIOUS PLAY MODES SUCH AS RANDOM, PROGRAM AND REPEAT HEADPHONE JACK WITH VOLUME RS-232C CONTROL PORT AND IR FLASHER INPUT RS-232C port which supports both unit control and operating status transmission is equipped to enable central control with custom installation. Also, Flasher input is equipped to realize wired control when you cannot use remote control due to the installation on the rack, etc. 5 SETS OF BUILT-IN REMOTE CONTROL CODES Because there are 5 sets of built-in remote control code signals for between the unit and remote controller, up to 5 units installed in the same place can be remotely controlled independently. ALUMINUM FRONT PANEL Hairline finish aluminum front panel is used for quality look. EQUIPMENT MAINS WORKING SETTING Your Marantz product complies with the household power and safety requirements in your area. This product can be powered by 120 V AC only. INAPPROPRIATE PLACES FOR INSTALLATION To keep your unit in perfect working order for the longest possible time, avoid installing the unit in the following locations. • Wherever it will be exposed to direct sunlight • Wherever it will be close to a heater or other heatradiating appliance • Wherever the humidity is high or ventilation is poor • Wherever it is very dusty • Wherever it will be subject to vibration • On top of a rickety stand or in an unstable location which is tilted at an angle • Near windows where there is a chance of exposure to rain, etc. • On top of an amplifier or other component which dissipates a great deal of heat To ensure proper heat dissipation, install the unit while leaving clearances between the unit and wall or other components, as shown in the figure below. Left 0.1 m (4 in) or more Above 0.1 m (4 in) or more Right 0.1 m (4 in) or more Rear 0.1 m (4 in) or more PRECAUTIONS • In winter, droplets of water form on the insides of the windows of a heated room: this is called condensation. This unit uses an optical lens, so the condensation may form in the following cases. - In a room immediately after the heating has been turned on - In a room where the humidity level is high - When the unit has been suddenly brought from a cold location into a warm room Since, in cases like this, the track numbers may not be read and the unit is prevented from operating properly, wait about 30 minutes, and then operate the unit. • If this unit is placed on an object that generates substantial heat, such as an amplifier, the laser inside this unit may be deteriorated. • This unit may cause interference on a tuner or TV set. If this is the case, place it further away from the tuner or TV set. • Compact discs have much less noise than analog records and hardly any noise is heard before play starts. Bear in mind, therefore, that if the volume control on the amplifier is set too high, you will risk damaging other audio components. • This unit cannot play CD-ROMs used with personal computers, game CDs, video CDs, DVDs (video/audio) or DTS-CDs. • We do not recommend the use of lens cleaners. • If this unit is placed in a rack with glass doors, do not attempt to open the disc tray with the 0 OPEN/CLOSE button on the remote controller with the glass doors shut. Impeded disc-tray movement may result in a failure. NOTES FOR REMOVING SHIPPING SCREWS At the bottom of the player there are two red shipping screws for use when the player is transported. Before using the player, turn these screws counterclockwise and remove them. If the shipping screws are still in place and the power is turned on, unplug the power cord from the power outlet and remove the shipping screws. Retain these screws as they will be needed when the player is transported. Before transporting the player, take out the discs, close the disc tray, set to standby mode and unplug the power cord from the power outlet. Then install the shipping screws by turning them clockwise. Be sure to fasten them securely. shipping screws ADVANCED OPERATIONS TROUBLESHOOTING OTHERS DO NOT PLACE OBJECTS ON TOP Refrain from placing any objects on top of the unit. 2