Marantz NR1501 NR1501 User Manual - English - Page 23
System Setup
View all Marantz NR1501 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 23 highlights
ENGLISH CONNECTIONS FUNCTIONS NAMES AND BASIC OPERATION ADVANCED CONNECTIONS 1. SYSTEM SETUP The unit's main functions are set following the steps below. SYSTEM SETUP SUB W MODE:NORMAL HDMI AUDIO OUT: OFF TONE CONTROL : OFF HT-EQ : OFF VIDEO CONVERT : AUTO RETURN TO MAIN MENU Press the 3/4 cursor buttons to move the cursor to the items to be set up. 1-1 SUB W MODE The subwoofer mode setting takes effect only when the front speaker has been set to FULL RANGE and the subwoofer to YES. This menu item setting takes effect only when PCM or analog stereo source signals are played. Tip For the settings of each speaker, refer to "3. SPEAKER/R.EQ SETUP" (page 21). Press the 1/2 cursor buttons to select NORMAL or SW PLUS+. • NORMAL The bass sound is reproduced through the main left and right speakers only. • SW PLUS+ The bass sound is reproduced through the main left and right speakers and subwoofer. In this playback mode, the bass sound disperses uniformly throughout the entire room. However, depending on the size and shape of the room, interference may arise, reducing the actual volume level of the bass sound. 1-2 HDMI AUDIO OUT This menu item is used to set whether the audio signals that have been input from the HDMI terminal are to be reproduced through the speakers connected to the unit or through the TV or projector connected to the unit's HDMI OUT terminal. Press the 1/2cursor buttons to select ON or OFF. • OFF The audio signals that have been input from the HDMI terminal are reproduced through the unit. In this case, sound audio signals will not be output from the TV or projector connected to the unit's HDMI OUT terminal. • ON The audio signals that have been input to the HDMI terminal are not output from the unit's speaker terminals. Instead, the audio data is output straight to the TV or projector connected to the unit's HDMI OUT terminal. This menu setting is used to listen to sound through a TV with a multi-channel capability. 1-3 TONE CONTROL This menu item is used to switch the tone controls to ON or OFF and set the tone controls. Press the 1/2 cursor buttons to select ON or OFF. • OFF The tone control function is disabled. • ON The tone control function is enabled. If the ENTER button on the remote controller is now pressed, the OSD menu appears on the display, and the tone control settings can be selected. TONE CONTROL >BASS : TREBLE : 0dB 0dB RETURN TO SYSTEM SETUP Press the 3/4 cursor buttons to select BASS or TREBLE. Then press the 1/2 cursor buttons to increment or decrement the decibel values shown. The tone controls can be adjusted in 1 dB steps up to +/-10 dB. After adjusting the tone controls, move the cursor to RETURN TO SYSTEM SETUP, and press the ENTER button. Notes The tone control function cannot be used in the modes listed below. • SOURCE DIRECT mode 1-4 HT-EQ When movies are played using audio components designed for the home, the treble range in their sound tracks is boosted, sometimes producing a somewhat shrill sound. This is because these sound tracks are designed to be played in the very large spaces inside movie theaters. However, if the HT-EQ function is enabled when watching movies designed for viewing at the movie theater, the sound will be compensated so that the appropriate tonal balance is attained. Press the 1/2 cursor buttons to select ON or OFF. The HT-EQ function cannot be used in the mode listed below. 1-5 VIDEO CONVERT This menu item is used to set the function for up-converting the analog video signals (video and component video signals) that are input to the unit to HDMI output signals. Press the 1/2 cursor buttons to select AUTO, COMPONENT, CVBS or OFF. • AUTO With this menu item setting, when there are no HDMI signals in the selected input function, the video or component video signals are detected automatically and up-converted to HDMI output signals. When both video and component video signals have been input, priority is given to up-converting the component video signals. SETUP • COMPONENT With this menu item setting, the component video signals that have been input to the unit are upconverted to HDMI output signals. • CVBS With this menu item setting, the video signals that have been input to the unit are up-converted to HDMI output signals. • OFF With this menu item setting, the unit's video-convert function is shut down. Notes • Only HDMI input signals can be connected to the BLU-RAY and GAME terminals on the unit's rear panel, so the video-convert function will not work. • HDMI digital video signals cannot be downconverted to analog video signals. • The signals up-converted to HDMI output signals are output without any processing at the resolution of the analog video signals that were input. When up-converting video or component video signals with a 480i resolution, a video monitor (TV set) supporting the 480i resolution must be connected to the unit. • Some analog video signals that are input to the unit cannot be detected automatically. In a case like this, select COMPONENT or CVBS, and use the signals in a fixed mode. • When HDMI signals have been input, priority will be given to the output of the HDMI signals, even while the COMPONENT or CVBS fixed mode is set. (The up-converted signals will not be output to HDMI output signals.) 19 BASIC SETUP ADVANCED OPERATION TROUBLESHOOTING OTHERS