Marantz SR-19EX Marantz AV Receiver IR Remote Code List - Page 20
Surround
View all Marantz SR-19EX manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 20 highlights
LEVEL 1/2 (SPEAKER LEVEL BY TEST TONE) LEVEL 1/2 SPKR LEVEL TEST TONE : OFF MODE : MANUAL FRONT L 0 dB TO NEXT LEVEL MENU SPKR LEVEL TEST TONE: Press the OK button, ON is indicated and the test tone starts from the front L-CH speaker. Press the OK button again, OFF is indicated and the output of the test tone will stop. MODE: Select the mode for generating the test tone. If you select AUTO, test tone will be output in a circular pattern which is Left --> Center Right --> Surround Right > Surround Left Subwoofer Left -p... 3 seconds for each channel. If you select MANUAL, press the OK or CH+ button to select the test tone channels. Channel: Adjust the level of test lone for each channel with the LVL+, LVL- or .4 / ► buttons of the RC-18SR. The current volume level is shown at the center of the display. Notes: The setup level for each channel is memorized to reproduce the all surround mode. These levels are common for all surround modes, except 6CH-DIRECT mode. In order to correctly set the output levels, use a hand-held Sound Pressure Level meter (SPL), set to C-Weighting and Slow averaging. A Radio Shacks SPL meter (catalogue number 330 - 2055) works well. Using the internal channel noise generators, set each channel so that you read 75 dB SPL from each channel." LEVEL 2/2 (BASS PEAK LEVEL LIMIT) LEVEL 2/2 BASS LEVEL BASS PEAK LEVEL TEST SIGNAL : STOP VOLUME : - 75dB ENTER RETURN TO MAIN/EXIT With Dolby Digital and DTS , not only the LFE (Low Frequency Effects), but also the bass of all channels can be heard from the Subwoofer or Large-speakers. This procedure prevents these speakers from becoming too loud and creating an unbalanced sound. Since the sound is output at a loud volume, perform this operation carefully. TEST SIGNAL: Press the OK button, START is indicated and a Bass test tone is generated from the speaker, according to SPK size setup. But the sound is not heard because the Master volume is set to automatically. Press ♦ button to move the cursor to VOLUME control. VOLUME: Adjust the bass test tone output level to where the bass sound begins to distort or maximum level with the VOL+, VOL- or 4/0- button. Press ♦ button to move the cursor to ENTER. ENTER: Press the OK button, ENTER is blinking and the Bass test tone stops. The Bass Peak Limit Level for your system has been memorized Notes: Each time the subwoofer level is changed, perform the Bass Peak Level setup and correct the setting. The bass peak limiter is not I 3 effective in STEREO reproducing for analog input and 96kHz-PCM, or SOURCE-DIRECT and 6CHANNEL-DIRECT modes are selected. The selected value is displayed in the volume column before the test signal starts. w SURROUND MODE SURROUND MODE MODE • STEREO NIGHT MODE : OFF LFE LEVEL : OdS RETURN TO MAIN/EXIT MODE: Select the surround mode with 4 or ► button. NIGHT MODE: Switch the NIGHT MODE ON or OFF with the 4 or ► button. Selecting the Night Mode ON is effective in Dolby Digital only, and it compresses the dynamic range by up to 1/4 to 1/3. This softens loud passages such as sudden explosions, to help prevent disturbing others late at night. LFE LEVEL: Select the output level of the LFE signal included in the Dolby Digital signal or the DTS signal. Select 0 dB, -10 dB or OFF with 4 or ► button. The level is ordinarily set to 0 dB except DTS-Music mode. In the DTS-Music mode, default level is set to -10 dB. REC COPY REC COPY VCR1 SOURCE TAPE : SOURCE DIGITAL : SOURCE RETURN TO MAIN/EXIT VCR1 COPY Select the visual source of the VCR1 output with 4 or ► button for video and audio dubbing to the VCR1 deck. The source is switched in the following sequence. SOURCE -> TV a LD DVD DSSNCR2 --+ AUX -*SOURCE To determine each source, display the desired source and press the OK button or ♦ / ♦ button. TAPE COPY Select the audio source of the TAPE output with 4 or ► button for audio dubbing to the tape deck. The source is switched in the following sequence. SOURCE -> TUNER -+ CD -> CD-R/MD SOURCE --> To determine each source, display the desired source and press the OK button or ♦ / ♦ button.