Marantz SR-19EX Marantz AV Receiver IR Remote Code List - Page 28
-31, firt5
View all Marantz SR-19EX manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 28 highlights
5. Press and hold the corresponding SIDE-A button on the laser 5. Continuing along, re-write the remaining letters "V", "-", "5", "2", disc player's remote transmitter until the head of name blinks in and "0". By pressing the cursor keys 4 and 10., each character is sc the RC-18SR LCD window or beep sounds emit. The RC-18SR confirmed in place. When you go to other DIRECT function he changes to the RENAME mode automatically as the next step. A pages by using the page function keys El characters in the (if function name of the DIRECT function button blinks, you can previous page are also confirmed in place. rename this blinking function name. You input the desired letter The name re-writing operation must be done on a function by or number with the ten keypad. (See the table in step 3 of the next function basis, that is, re-write the names for all of the LD direct procedure for referece.) If you need not rename, press the OK functions, then switch to another function such as VCR, and button or the other buttons except the ten keypad. begin the re-writing process anew to re-name the VCR direct 6. Now, proceed to program the other commands from the laser function commands. After completing all re-writing of any of the disc player's remote transmitter to the other DIRECT function names, press the OK button within the cursor keys al. buttons (02-D8). When you have "taught" all 8 direct functions it rly for Page 1, press the page direction key). L to go to Page 2, and you can program more direct function keys. 7. After memorizing all codes to all DIRECT function buttons, press the operation MODE button CI with the tip of a paper clip and. return the RC-18SR to the USE mode. Now, the newly memorized How to re-write the STATUS name: Using the same steps as outlined above, you can re-write the 9 character status name. During step 5 above, by pressing the up and down cursor keys® the left side of the status indicator begins blinking, and you can change its display according to.the same ed codes are usable from the RC-18SR. method outlined above, using the 10 keypad character generator. )w, If you wish, you can re-write the names for each function name, status Remember, to confirm each character change, use the cursor keys 4 ;as name, and the direct function command names as follows: and II.. As above, when you change the direct function page by ed Tie For our example, you can change the LCD display window indication from "LD" to "LV-520" (which is the model number for a Marantz laser pressing the page direction keys [D, this will confirm the re-written characters in place as well for the page you just finished re-naming. dar disc player). Remember, you can re-name a function selector button You have up to 9 letters, numbers or other characters available for with a new name of up to six characters of letters and numbers in any each status name. ce )P, by ce ing combination. 1. Using the tip of a paper clip, press the operation MODE button M until the NAME indicator appears and begins to blink in the LCD window, 2. Choose a button that you wish to re-name, in this case, press the "LD" function button 0. In the LCD window, the first character of the six function character display indicators starts blinking "A", How to re-write the DIRECT function button names: You can change the name for each of the 8 direct function buttons by using the steps described above to change main function name and status name. Remember, each main function has 8 direct function buttons on each of the 4 pages, so you have up to 32 direct functions that can be re-named, if you wish, for each of the 11 main function :ps 1 is the which is the first letter of the alphabet if you press "1" button twice. 3. Choose the desired letter or number by pressing the 10 keypad buttons g. Each 10 keypad button has 4 characters attached to selection buttons El. You have up to 4 characters available for each direct function button name. After completing all re-writing of any of the names, press the OK button within the cursor keys a or switch to another function button put it as follows: (such as CD). If, during re-naming, a button has not been pressed for 10 keypad button Press, press again, press again, etc. 1 minute, the RC-18SR will revert to the prior operating mode (USE) ion ISE 1SE ble 1 1 -4A -4B -4C->1-4 2 2 -4D -4E -4F-42-4 3 3 -4G ->H -- I-43-4 4 4 -)..1-4K -4L-)4-4 5 5-M--,N1->O-5- automatically. If re-writing of all of the desired direct mode functions has been completed, use the tip of a paper clip to press the operation MODE button P, and select the "USE" mode. Now, all of the re-written names are available for use. 6 6 -4P ->Q -4R->6-+ 7 7 ->S -4T ->U-47-4 How to clear (erase) the memorized codes 8 8 ->V---)W--> X -4 8> (and any re-written names): 9 9 -4Y ->Z-4/-49-4 The RC-18SR has a high capacity RAM, which ordinarily will allow the 0 0 -+ -4 - -4 SPACE -a, -4 ' -4 0 learning of several hundred remote codes (and their associated new names, if desired). However, due to the fact that some remote codes So, in the above example, by pressing the 10 keypad number 4 four occupy more memory space than others, it is possible that the times, you get the letter "L" to appear in the display (see Figure 4). available RAM fills up completely, and the "FULL" indicator appears tory Figure 4 in the LCD window. In this case, it will not be possible to learn any new remote codes without first deleting some or all of the previously LC) }rim learned remote codes and/or re-written names. There are 4 ways to erase learned remote codes from memory: tion 511-R RPTR • Erasing by button(s) 5.11-31 RPTB • Erasing by DIRECT button(s) N5P EP/F • Erasing by function(s) firt5 ENT • Erasing all memory contents (complete erasure) tion -ect 2 f 4 4. You use the cursor buttons' and ► a to move to the next •• Note that the factory-programmed RC-5 codes are not stored in RAM, and are therefore not erasable. character in the display. By pressing the right cursor button For any of these memory erasure options, you must first set the RC- the the letter "L" is confirmed in the first character space in the LCD 18SR to LEARN mode. kRN window and the next character position begins blinking. If you wish to erase a previously memorized character, position the Erasing the memory assigned to a particular button: )Iler cursor over the character and put the SPACE character in its Press and hold the CLEAR button a and press the button that you fri ed place (the SPACE character is ten keypad number 0 pressed four wish to erase 2 times. The code previously learned by that button will art. times, from the above character chart). be erased, and will then be either empty, or the original factory provided RC-5 code will re-appear in its place. rect r44