Marantz SR7400 SR7400 User Guide - Page 9

ENGLISH REAR PANEL qw e r ty u io ANTENNA COMPONENT VIDEO INPUT-1 Y CB/PB CR/PR INPUT-2 Y CB/PB CR/PR MONITOR OUT Y CB/PB CR/PR FM (75Ω) GND AM VIDEO TV DVD VCR1 IN OUT DSS/VCR2 MONITOR MULTI TV IN OUT OUT OUT DVD VCR1 IN OUT S-VIDEO DSS/VCR2 MONITOR IN OUT OUT RS-232C 1 TV L R DIGITAL IN 2 3 4 DVD VCR1 IN OUT MULTI RC-5 RC FLASHER IN L DIGITAL OUT IN 5 6 OPT. COAX. DSS/VCR2 CD TAPE OUT CDR/MD DC OUT R MULTI L SL SBL C PRE OUT SR SL SBR SBL SW C IN OUT 7.1CH IN IN OUT IN OUT OUT R SR SBR SW AUDIO (AUX2) MODEL NO.SR7400 R L SURROUND BACK / MULTI SPEAKER AC IN SWITCHED UNSWITCHED 1A 120W MAX 1A 120W MAX AC OUTLETS 120V 60HZ R L R L R L FRONT A FRONT B CENTER SPEAKER SYSTEMS FRONT A OR B, CENTER, SURROUND, SURR. BACK : MINIMUM 6 OHMS FRONT A AND B : MINIMUM 8 OHMS SURROUND !9 !8 !7 !6 !5 !4 !3 !2 !1 !0 q VIDEO IN/OUT (TV, DVD, VCR1, DSS/VCR2) These are the video inputs and outputs. There are 4 video inputs and 2 video outputs and each one includes both composite video and S-video configurations. Connect VCRs, DVD players, and other video components to the video inputs. S-video sources can be viewed through the Svideo outputs, and composite sources can only be viewed through the composite output. The 2 video output channels can be used to be connected to video tape recorders for making recordings. w FM antenna terminal (75 ohms) Connect an external FM antenna with a coaxial cable, or a cable network FM source. AM antenna and ground terminals Connect the supplied AM loop antenna. Use the terminals marked "AM" and "GND". The supplied AM loop antenna will provide good AM reception in most areas. Position the loop antenna until you hear the best reception. e COMPONENT VIDEO INPUT/OUTPUT If your DVD player or other device has component video connectors, be sure to connect them to these component video connectors on the SR7400. The SR7400 has two component video input connectors to obtain the color information (Y, CB, CR) directly from the recorded DVD signal or other video component and one component video output connector to output it directly into the matrix decoder of the display device. By sending the pure DVD component video signal directly, the DVD signal forgoes the extra processing that normally would degrade the image. The result is vastly increased image quality, with incredibly life like colors and crisp detail. r FLASHER IN (Flasher input terminal) This terminal is to control the unit from each zone. Connect the control signal from a Keypad, etc. t MONITOR OUT This is a monitor output and each one includes both composite video and S-video configurations. When connecting two video monitors or televisions, be aware that the OSD interface can be used with both MONITOR OUT connections. y RS-232C The RS-232C port is to be used in conjunction with an external controller to control the operation of the SR7400 by using an external device. The RS-232C port may also be used in the future to update the operating software of the SR7400 so that it will be able to support new digital audio formats and the like as they are introduced. u Preamp Outputs (L, R, SL, SR, SBL, SBR, C) Jacks for L(front left), R (front right), C (Center), SL (surround left), SR (surround right), SBL (surround back left) and SBR (surround back right). Use these jacks for connection to external power amplifiers. i AC INLET Plug the supplied power cord into this AC INLET and then into the power outlet on the wall. SR7400 has to be powered by 120 V AC only. o AC OUTLETS Connect the AC power cables of components such as a DVD and CD player to these outlets. SWITCHED and UNSWITCHED outlets are provided. The one marked SWITCHED provides power only when the SR7400 is turned on and is useful for components which you use every time you play your system. The one marked UNSWITCHED is always live as long as the SR7400 is plugged into a live outlet. A component connected here may be left on permanently, or may be switched off with via its own power switch. Caution: • In order to avoid potential turn-off thumps, anything plugged into these outlets should be powered up before the SR7400 is turned on. • The capacity of this AC outlet is 120W. Do not connect devices that consume electricity more than the capacity of these AC outlets. If the total power consumption of the connected devices exceeds the capacity, the protection circuit shuts down the power supply. !0 Speaker outputs terminals Seven terminals are provided for the front (A) left, front (A) right, front (B) left, front (B) right, front center, surround left and surround right speakers. !1 Speaker outputs terminals (for multi room or surround back) Two terminals are provided for the front the left, and right speakers for multi room (2nd zone) or surround back. !2 Subwoofer Output Connect this jack to the line level input of a powered subwoofer. If an external subwoofer amplifier is used, connect this jack to the subwoofer amplifier input. If you are using two subwoofers, either powered or with a 2 channel subwoofer amplifier, connect a "Y" connector to the subwoofer output jack and run one cable from it to each subwoofer amplifier. !3 7.1 CHANNEL or AUX2 INPUT By connecting a DVD Audio player, SACD multichannel player, or other components that has a multichannel port, you can playback the audio with 5.1 channel or 7.1 channel outputs. !4 DC TRIGGER output terminal Connect a device that needs to be triggered by DC under certain conditions (screen, power strip, etc...) Use the system OSD setup menu to determine the conditions by which these jack will be active. Note: • This output voltage is for (status) control only, It is not sufficient for drive capability. !5 Multiroom Outputs (Audio L&R, Video) These are the audio and video output jacks for the Multi zone (Multi room). Connect these jacks to optional audio power amplifiers or video display devices to listen and view the source selected by the multiroom system in a remote room. !6 MULTI ROOM REMOTE IN/OUT terminals IN: Connect to a multi-room remote control device, available from your Marantz dealer. OUT: Connect to the Marantz component equipped with remote control (RC-5) terminals in Multi zone (Multi room). !7 REMOTE CONT. IN/OUT terminals Connect to a Marantz component equipped with remote control (RC-5) terminals. 6