Maytag HRE2940T User Guide - Page 8

Instructions for Installation

Page 8 highlights

Instructions for Installation Removing the Old Water Heater 1 Turn "OFF" electrical supply to the water heater. 2 Turn "OFF" the water supply to the water heater at the water shutoff valve or water meter. 5 a. If you have copper piping to the water heater, the two copper water pipes can be cut with a hacksaw approximately four inches away from where they connect to the water heater. This will avoid cutting off the pipes too short. Additional cuts can be made later if necessary. Disconnect the temperature-pressure relief valve drain line. When the water heater is drained, disconnect the hose from the drain valve. Close the drain valve. The water heater is now completely disconnected and ready to be removed. 2 1 5 3 Attach a hose to the water heater drain valve and put the other end in a floor drain or outdoors. Open the water heater drain valve. Open a nearby hot water faucet which will relieve pressure in the water heater and speed draining. WARNING The water passing out of the drain valve may be extremely hot. To avoid being scalded, make sure all connections are tight and that the water flow is directed away from any person. 4 5 b. If you have galvanized pipe to the water heater, loosen the two galvanized pipes with a pipe wrench at the union in each line. Also disconnect the piping remaining to the water heater. These pieces should be saved since they may be needed when reconnecting the new water heater. Disconnect the temperature-pressure relief valve discharge pipe. When the water heater is drained, disconnect the hose from the drain valve. Close the drain valve. The water heater is now completely disconnected and ready to be removed. 3 4 Check again to make sure the electrical supply is turned "OFF" to the water heater. Then disconnect the electrical supply connection from the water heater junction box. CAUTION Mineral buildup or sediment may have accumulated in the old water heater. This causes the water heater to be much heavier than normal and this residue, if spilled out, could cause staining. 8

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36

8
Instructions for Installation
Attach a hose to the water heater drain
valve and put the other end in a floor
drain or outdoors. Open the water
heater drain valve. Open a nearby hot
water faucet which will relieve pressure
in the water heater and speed draining.
Check again to make sure the electrical supply is turned
“OFF” to the water heater. Then disconnect the electri-
cal supply connection from the water heater junction
box.
2
5
1
4
5
3
a.
If you have copper piping to the water heater, the two
copper water pipes can be cut with a hacksaw approxi-
mately four inches away from where they connect to
the water heater. This will avoid cutting off the pipes
too short. Additional cuts can be made later if neces-
sary. Disconnect the temperature-pressure relief valve
drain line. When the water heater is drained, discon-
nect the hose from the drain valve. Close the drain
valve. The water heater is now completely disconnect-
ed and ready to be removed.
b. If you have galvanized pipe to the water
heater, loosen the two galvanized pipes
with a pipe wrench at the union in each
line. Also disconnect the piping remain-
ing to the water heater. These pieces
should be saved since they may be needed
when reconnecting the new water heater.
Disconnect the temperature-pressure
relief valve discharge pipe. When the
water heater is drained, disconnect the
hose from the drain valve. Close the drain
valve. The water heater is now completely
disconnected and ready to be removed.
4
2
3
Turn “OFF” the water supply to the
water heater at the water shutoff valve
or water meter.
5
Turn “OFF” electrical supply to the water heater.
1
Removing the Old Water Heater
WARNING
The water passing out of the drain
valve may be extremely hot. To
avoid being scalded, make sure all
connections are tight and that the
water flow is directed away from
any person.
CAUTION
Mineral buildup or sediment may have accumulated
in the old water heater. This causes the water
heater to be much heavier than normal and this
residue, if spilled out, could cause staining.