Maytag MBB1952HEW Use and Care Guide - Page 6

Pullout Freezer Drawer - refrigerator model

Get Maytag MBB1952HEW - 19 cu. Ft. Bottom Mount Refrigerator PDF manuals and user guides View all Maytag MBB1952HEW manuals
Add to My Manuals
Save this manual to your list of manuals

Page 6 highlights

Installation Pullout Freezer Drawer (select models) DANGER To prevent accidental child entrapment or suffocation risk, do not remove the divider in the top freezer basket. WARNING To avoid electrical shock which can cause severe personal injury or death, disconnect power to refrigerator before removing doors. After replacing doors, connect power. CAUTION To avoid possible injury, product, or property damage, you will need two people to perform the following instructions. Materials Needed: • Phillips screwdriver To Remove: 1. Pull drawer open to full extension. 2. Tilt the lower basket forward and lift to remove. 3. On each white drawer bracket is a basket cradle with two snap attachments. To release each cradle, unlatch the snaps by pushing them inward, away from the side bracket. Lift the cradles off of the rails. 4. Remove Phillips screw from each of the drawer slides (select models). 5. Lift top of drawer front to unhook the drawer from the slides. Lift door front out to remove. To Install: 1. Pull both rails out to full extension. 2. While supporting door front, hook supports into slots located on inside of each slide. Note: All four drawer bracket supports must be in the proper slots for the drawer to function properly. 3. Lower door front into final position. 4. Replace and tighten Phillips screws that were removed from the drawer slides (select models). 5. Place the basket cradles back onto the drawer slides. Align basket cradle snaps with the slots on the drawer brackets and press each cradle toward the bracket until it clicks. Basket cradle snap attachments 6. Tilt the lower basket front down and set it down into the basket cradles. 5

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
5
Installation
Pullout Freezer Drawer
(select models)
To avoid electrical shock which can cause severe
personal injury or death, disconnect power to
refrigerator
before
removing doors. After replacing
doors, connect power.
WARNING
To prevent accidental child entrapment or
suffocation risk,
do not
remove the divider in the
top freezer basket.
DANGER
To avoid possible injury, product, or property
damage, you will need two people to perform the
following instructions.
CAUTION
Materials Needed:
•
Phillips screwdriver
To Remove:
1. Pull drawer open to full extension.
2. Tilt the lower basket
forward and lift to remove.
3. On each white drawer
bracket is a basket cradle
with two snap attachments.
To release each cradle,
unlatch the snaps by
pushing them inward,
away from the side
bracket. Lift the cradles
off of the rails.
4. Remove Phillips screw
from each of the drawer
slides (select models).
5. Lift top of drawer front
to unhook the drawer
from the slides. Lift
door front out to
remove.
To Install:
1. Pull both rails out to
full extension.
2. While supporting
door front, hook
supports into slots
located on inside of
each slide.
Note:
All four drawer bracket supports must be in
the proper slots for the drawer to function properly.
6. Tilt the lower basket front down and set it down
into the basket cradles.
Basket cradle
snap attachments
3. Lower door front into final position.
4. Replace and tighten Phillips screws that were
removed from the drawer slides (select models).
5. Place the basket cradles back onto the drawer
slides. Align basket cradle snaps with the slots on
the drawer brackets and press each cradle toward
the bracket until it clicks.