Home » Maytag Manuals » Laundry Washers » Maytag MHWZ600TW » Manual Viewer

Maytag MHWZ600TW Use and Care Guide - Page 6

Location Requirements - pedestals

UPC - 883049064352

Add to My Manuals
Save this manual to your list of manuals

Page 6 highlights

Location Requirements Selecting the proper location for your washer improves performance and minimizes noise and possible washer "walk." Your washer can be installed under a custom counter, or in a basement, laundry room, closet, or recessed area. See "Drain System." Companion appliance location requirements should also be considered. Proper installation is your responsibility. You will need „ A water heater set to deliver 120°F (49°C) water to the washer. „ A grounded electrical outlet located within 6 ft (1.8 m) of where the power cord is attached to the back of the washer. See "Electrical Requirements." „ Hot and cold water faucets located within 4 ft (1.2 m) of the hot and cold water fill valves, and water pressure of 20-100 psi (137.9-689.6 kPa). „ A level floor with a maximum slope of 1" (25 mm) under entire washer. Installing the washer on soft floor surfaces, such as carpets or surfaces with foam backing, is not recommended. „ A sturdy and solid floor to support the washer with a total weight (water and load) of 400 lbs (180 kg). Do not operate your washer in temperatures below 32°F (0°C). Some water can remain in the washer and can cause damage in low temperatures. See "Washer Care" for information on winterizing. Installation clearances „ The location must be large enough to allow the washer door to be fully opened. „ Additional spacing should be considered for ease of installation and servicing. The door opens more than 90°, and it is not reversible. „ Additional clearances might be required for wall, door, and floor moldings. „ Additional spacing of 1" (25 mm) on all sides of the washer is recommended to reduce noise transfer. „ Companion appliance spacing should also be considered. Washer Dimensions 50¼" (1276 mm) 27" (686 mm) 36" (914 mm) 30½" (775 mm) Door is not reversible. Recommended installation spacing for custom undercounter installation The dimensions shown are for the recommended spacing. Custom undercounter installation - Washer only 37" min. (939 mm) 1" (25 mm) 27" (686 mm) 1" (25 mm) Recommended installation spacing for recessed or closet installation, with or without a pedestal The dimensions shown are for the recommended spacing. 6

Section	Page
PERFORMANCE SERIES	1
automatic washer	1
Use & Care Guide	1
LAVEUSE AUTOMATIQUE	1
GUIDE D’UTILISATION ET D’ENTRETIEN	1
FOR QUESTIONS ABOUT FEATURES, OPERATION/PERFORMANCE, PARTS, ACCESSORIES OR SERVICE CALL: 1.800.688.9900 IN CANADA, CALL: 1.800.807.6777	1
AU CANADA, POUR DES QUESTIONS À PROPOS DES CARACTÉRISTIQUES, DU FONCTIONNEMENT/ RENDEMENT, DES PIÈCES, DES ACCESSOIRES OU DU SERVICE, COMPOSEz LE : 1.800.807.6777	1
VISIT OUR WEBSITE AT WWW.MAYTAG.COM IN CANADA, WWW.MAYTAG.CA	1
OU VISITEZ NOTRE SITE INTERNET À WWW.MAYTAG.CA	1
PARA OBTENER ACCESO AL MANUAL DE USO Y CUIDADO EN ESPAÑOL, O PARA OBTENER INFORMACIÓN ADICIONAL ACERCA DE SU PRODUCTO, VISITE: WWW.MAYTAG.COM. TENGA LISTO SU NÚMERO DE MODELO COMPLETO. PODRÁ ENCONTRAR EL NÚMERO DE MODELO Y DE SERIE EN LA ETIQUET...	1
Certified to Sanitize	1
Certifié pour aseptiser	1
Designed to use only HE High Efficiency detergent	1
Conçue pour l’utilisation d’un détergent HE haute efficacité seulement	1
Table of Contents	2
TABLE DEs MATIÈRES	2
WASHer Safety	3
INSTALLATION requirements	5
Tools and Parts	5
Tools needed for connecting the water inlet hoses	5
Tools needed for connecting the drain hose	5
Tools needed for installation	5
Alternate Parts	5
Options	5
Pedestal	5
Optional pedestal	5
Stack Kit	5
Location Requirements	6
Installation clearances	6
Washer Dimensions	6
Recommended installation spacing for custom undercounter installation	6
Recommended installation spacing for recessed or closet installation, with or without a pedestal	6
Recommended installation spacing for recessed or closet installation, with stacked washer and dryer	7
Recommended installation spacing for cabinet installation	8
Drain System	8
Standpipe drain system - wall or floor (views A & B)	8
Laundry tub drain system (view C)	8
Floor drain system (view D)	8
Electrical Requirements	9
installation instructions	10
Remove Transport System	10
1. On the back of the washer, loosen the 4 transport bolts using a 13 mm wrench.	10
2. Once the bolt is loose, move it to the center of the hole and completely pull out the bolt, including the plastic spacer covering the bolt.	10
3. Once all 4 bolts are removed, discard the bolts and spacers. Then pull the power cord through the opening of the rear panel and close the hole with the attached cap.	10
4. Cover the bolt holes with the 4 transport bolt hole plugs.	10
Connect the Inlet Hoses	10
Connect the inlet hoses to the water faucets	10
1. Attach a hose to the hot water faucet. Screw on coupling by hand until it is seated on the washer.	10
2. Attach a hose to the cold water faucet. Screw on coupling by hand until it is seated on the washer.	10
3. Using pliers, tighten the couplings with an additional two-thirds turn.	10
Clear water lines	10
Connect the inlet hoses to the washer	11
1. Attach the hot water hose to the washer’s hot (H) water inlet valve. Screw on coupling by hand until it is seated on the washer.	11
2. Attach the cold water hose to the washer’s cold (C) water faucet. Screw on coupling by hand until it is seated on the washer.	11
3. Using pliers, tighten the couplings with an additional two-thirds turn.	11
4. Turn on the water faucets completely and check for leaks.	11
Connect the Drain Hose	11
1. Use locking pliers, squeeze hose clamp tabs together and insert over the end of drain hose.	11
2. Slide drain hose onto washer connection.	11
3. Once drain hose is in place, release pliers.	12
4. Washer drain system can be installed using a floor drain, wall standpipe, floor standpipe, or laundry tub.	12
Floor drain	12
Secure the Drain Hose	12
1. Drape the power cord over the washer top.	12
2. Move the washer to its final location.	12
3. Place the drain hose in the laundry tub or standpipe as shown. See illustrations A and B.	12
4. If the washer faucets and the drain standpipe are recessed, put the hooked end of the drain hose in the standpipe as shown. See illustration C.	12
Level the Washer	12
1. Slide the washer to its final location.	12
2. Check that all four feet are in firm contact with the floor.	12
3. Check the levelness of the washer by placing a level on the top edge of the washer, first side to side then front to back.	12
4. Make sure all four feet are stable and resting on the floor. Then check that the washer is perfectly level (use a level). Repeat steps 1-3 until washer is level.	12
5. After the washer is level, and all four feet are in firm contact with the floor, use a 9/16\	13
6. The washer should not move front to back, side to side, or diagonally when pushed on its top edges.	13
7. Confirm the levelness of the washer.	13
Complete Installation	13
1. Check the electrical requirements. Be sure that you have the correct electrical supply and the recommended grounding method. See “Electrical Requirements.”	13
2. Check that all parts are now installed. If there is an extra part, go back through the steps to see which step was skipped.	13
3. Check that you have all of your tools.	13
4. Dispose of/recycle all packaging materials.	13
5. Check that the water faucets are on.	13
6. Check for leaks around faucets and inlet hoses.	13
7. Plug into a grounded 3 prong outlet.	13
8. Read “Washer Use.”	13
9. To test and to clean your washer, measure ½ the detergent manufacturer’s recommended amount of HE High Efficiency detergent for a medium-size load. Pour the detergent into the detergent dispenser. Select NORMAL, and then select START. Allow the...	13
Use only HE High Efficiency detergent.	13
FEATURES AND BENEFITS	14
Electronic Controls	14
Auto Water Level	14
Larger Load Size	14
Suspension System	14
Stainless Steel Drum	14
Adaptive Variable Speed Motor	14
Spin Speeds	14
Thermal Optimizer	14
Certified to Sanitize	14
Add A Garment	14
Dynamic Balance	14
Detergent Advantage System Dispenser	14
Use only HE High Efficiency detergent.	14
washer USE	15
Note: The panel shown above may be different from that of your model.	15
Starting Your Washer	15
Using the Proper Detergent	15
Use only HE High Efficiency detergent.	15
First Wash Cycle Without Laundry	15
For All Wash Cycles	16
1. To load washer Open the washer door by pulling on the handle. Sort laundry according to color and type of fabric. Place a load of sorted clothes in the washer. Do not overload washer. Overloading can cause poor cleaning.	16
2. Close the washer door by pushing it firmly until the lock clicks. The washer door will remain locked during the wash cycle.	16
3. Open the dispenser drawer and add laundry products to the detergent, bleach, or fabric softener compartments. Close drawer slowly to avoid spills. See “Using the Dispenser.”	16
4. Turn on the washer by selecting POWER. Select one of the cycles by turning the cycle selector. The indicator light for the selected cycle will illuminate. When selecting a Wash Cycle, the preset Modifiers and Options, Water Temp, and Spin Speed fo...	16
5. Select the desired OPTIONS such as Prewash, MAX EXTRACT™, Stain Cycle, or Extra Rinse. Not all Options are available with all cycles. See “Options.”	16
6. Select the desired MODIFIERS, such as Spin Speed and Wash/Rinse Temp. Not all Modifiers are available with all Cycles and Options. See “Modifiers.”	16
7. If desired, select the CYCLE SIGNAL. The signal is helpful when you are washing items that should be removed from the washer as soon as it stops. Press CYCLE SIGNAL once to turn it on. The indicator light will illuminate. Press again to turn it off.	16
8. To begin the wash cycle immediately Select and hold START (for approximately 1 second).	16
9. To begin the wash cycle later Select DELAY WASH until the desired delay time (in hours) shows in the Estimated Time Remaining display. Select START. The countdown to the wash cycle will show in the display window.	16
Using the Dispenser	16
Choosing the Right Detergent	16
Use only HE High Efficiency detergent.	16
To fill dispenser compartments	16
1. Pull out the dispenser drawer.	16
2. Add the desired laundry product to the proper compartment.	16
3. Push in the dispenser drawer slowly and completely (to avoid a spill).	17
Dispenser	17
Main Wash detergent compartment	17
Chlorine bleach compartment	17
Fabric softener compartment	17
Pausing or Restarting	17
1. To pause the washer at any time, select PAUSE/CANCEL.	17
2. To continue the cycle, select and hold START (for approximately 1 second).	17
Changing Cycles, Options, and Modifiers	17
To stop a cycle and select a new cycle	17
1. Select PAUSE/CANCEL twice.	17
2. Select POWER.	17
3. Select desired cycle.	17
4. Select the desired OPTIONS such as Prewash, MAX EXTRACT™, Stain Cycle, or Extra Rinse.	17
5. Select the desired MODIFIERS such as Spin Speed or Wash/Rinse Temp.	17
6. Select and hold START (for approximately 1 second) to restart the washer at the beginning of the new cycle.	17
To cancel a cycle	17
1. Select PAUSE/CANCEL twice.	17
2. The washer powers down, the door unlocks, and clothes can be removed.	17
To change Options or Modifiers after the cycle has started	17
1. Select PAUSE/CANCEL.	17
2. Select the desired Spin Speed, Wash/Rinse Temp, or OPTION (such as Prewash, MAX EXTRACT™, Stain Cycle, or Extra Rinse). If the modifier or option are not available, the machine will beep.	17
3. Select and hold START (for approximately 1 second) to continue the cycle.	17
To drain the washer manually	17
1. Select PAUSE/CANCEL.	17
2. Select SPIN Only.	17
3. Select and hold START (for approximately 1 second) to begin the drain.	17
4. When the spin is complete, the door unlocks. Items can be removed from the washer.	17
Status Lights	18
Adding items	18
1. Select PAUSE/CANCEL. The washer door unlocks, and items can be added.	18
2. To continue the cycle, close the door and select and hold START (for approximately 1 second).	18
Clean	18
Locking controls	18
Estimated Time Remaining	18
Door Locked	18
Cycles	18
Wash Cycles	18
Preset Cycle Settings	19
Cycle	19
Estimated Time* (hr:min)	19
Wash/Rinse Temp	19
Spin Speed	19
Sanitary	19
Certified to Sanitize	19
Whites	19
Super Wash	19
Normal	19
Rapid Wash	19
Delicate	19
Handwash	19
Spin Only	19
Rinse & Spin	20
Clean Washer	20
Normal Sounds	20
Options	20
Prewash	20
Stain Cycle	20
Extra Rinse	20
Cycle Signal	20
Modifiers	20
Wash/Rinse Temp	21
Temperature Guide	21
Auto Temp Control	21
Laundry Guide	21
Refer to this chart for suggested load types and their corresponding cycles. Listed to the right are the options available to each of these washer cycles.	21
Available Options	21
4	21
4	21
4	21
4	21
4	21
4	21
4	21
4	21
4	21
4	21
4	21
4	21
4	21
4	21
4	21
4	21
4	21
4	21
4	21
4	21
4	21
4	21
4	21
4	21
4	21
4	21
4	21
4	21
4	21
4	21
4	21
4	21
4	21
4	21
4	21
4	21
4	21
Laundry Tips	22
Preparing clothes for washing	22
Use only HE High Efficiency detergent.	22
Sorting	22
Unloading	22
Loading	22
Loading suggestions	22
Stain Removal Guide	23
Ink	23
4	23
Grass	23
4	23
Blood	23
4	23
Tomato Products	23
4	23
Coffee/Chocolate	23
4	23
Mud	23
4	23
Cosmetics	23
Dirty Motor Oil	23
Ring around the Collar	23
4	23
Washer care	24
Cleaning Your Washer	24
Cleaning the Door Seal/Bellow	24
1. Open the washer door and remove any clothing or items from the washer.	24
2. Inspect the colored seal/bellow between the door opening and the basket for stained areas. Pull back the seal/bellow to inspect all areas under the seal/bellow and to check for foreign objects.	24
3. If stained areas are found, wipe down these areas of the seal/bellow, using the procedure that follows.	24
a) Mix a dilute solution, using ¾ cup (177 mL) of liquid chlorine bleach, and 1 gal. (3.8 L) of warm tap water.	24
b) Wipe the seal/bellow area with the dilute solution, using a damp cloth.	24
c) Let stand 5 minutes.	24
d) Wipe down area thoroughly with a dry cloth and let the washer interior air dry with door open.	24
Washer Maintenance Procedure	24
Begin procedure	24
1. Open the washer door and remove any clothing or items from the washer.	24
2. Using the AFFRESH® washer cleaner (Recommended): Add one AFFRESH® washer cleaner tablet to the washer drum. If using liquid chlorine bleach: Open the dispenser drawer and immediately add 2/3 cup (160 mL) of liquid chlorine bleach to the bleach c...	24
3. Close the washer door and dispenser drawer.	24
4. Select the CLEAN WASHER cycle.	24
5. Press START.	24
6. The cycle will determine whether clothing or other items are in the washer.	24
7. Once the cycle has begun, allow the cycle to complete.	24
8. After the cycle is complete, leave the door open slightly, to allow for better ventilation, and drying of washer interior.	24
Always do the following to maintain washer freshness	24
Cleaning the exterior	24
Cleaning the dispenser drawer	25
1. Unlock the dispenser drawer by pressing the dispenser release lever (letter A in Dispenser Illustration, see “Using the Dispenser”). Remove the drawer.	25
2. Remove the inserts (the siphon from the softener and bleach compartments).	25
3. Wash the parts under running water.	25
4. Replace the inserts and return the dispenser to the drawer.	25
Water Inlet Hoses	25
Vacation, Storage, and Moving Care	25
Non-use or vacation care:	25
To winterize washer:	25
1. Put 1 qt (1 L) of R.V.-type antifreeze in the drum.	25
2. Run washer on a Drain & Spin cycle.	25
3. Unplug washer or disconnect power.	25
4. Shut off both water faucets.	25
5. Disconnect water inlet hoses from faucets and drain.	25
To use washer again:	25
1. Flush water pipes.	25
2. Reconnect water inlet hoses to faucets.	25
3. Turn on both water faucets.	25
4. Plug in washer or reconnect power.	25
5. Run the washer through the Normal cycle with ½ the manufacturer’s recommended amount of HE detergent for a medium-size load, to clean the washer and remove the antifreeze, if used.	25
To transport the washer:	25
1. If washer will be moved during freezing weather, put in 1 qt (1 L) of R.V.-type antifreeze in the drum. Run washer on a Drain & Spin cycle.	25
2. Unplug the power cord.	25
3. Disconnect the drain hose from the drain system and attach to rear panel clips.	25
4. Shut off both water faucets.	25
5. Disconnect the water inlet hoses from faucets, then drain the hoses and clip them to the rear panel of the washer.	25
6. IMPORTANT: Call service. Do not reuse transport bolts. Washer must be transported in the upright position. To avoid suspension and structural damage, your machine must be properly set up for relocation by a certified technician.	25
Reinstalling the washer	25
1. Follow the “Installation Instructions” to locate, level and connect the washer.	25
2. Run the washer through the Normal cycle with ½ the manufacturer’s recommended amount of HE detergent for a medium-size load, to clean the washer and remove the antifreeze, if used.	25
troubleshooting	26
First try the solutions suggested here or visit our website and reference FAQs (Frequently Asked Questions) to possibly avoid the cost of a service call. in U.S.A. www.maytag.com/help In Canada www.maytag.ca	26
Error codes	26
Noisy, vibrating, off-balance	26
Leaking	26
Dispenser operation	27
Washer odor	27
Door won't unlock	27
Washer won't power up	27
Washer cycle won’t start	27
Control won’t accept selections or won’t shut off	27
Washer stops working	28
Washer won’t dispense	28
Washer won’t fill	28
Washer won’t run	28
Incorrect water temperature or Wash/Rinse temperature	28
Not enough water/Not enough suds	28
Washer continues to fill or drain, cycle seems stuck	28
Washer won’t drain or spin, water remains in washer	28
Cycle time changes/Cycle too long	29
Clothes Care	29
Load too wet	29
Residue, lint, stains on load; gray whites, dingy colors	29
Load is wrinkled, twisted, tangled	29
Assistance or Service	30
If you need replacement parts	30
In the U.S.A.	30
For further assistance	30
In Canada	30
For further assistance	30
Accessories	30
MAYTAG® LAUNDRY WARRANTY	31
LIMITED WARRANTY	31
For one year from the date of purchase, when this major appliance is operated and maintained according to instructions attached to or furnished with the product, Maytag brand of Whirlpool Corporation or Whirlpool Canada LP (hereafter “Maytag”) wi...	31
ITEMS EXCLUDED FROM WARRANTY	31
This limited warranty does not cover:	31
1. Replacement parts or repair labor if this major appliance is used for other than normal, single-family household use or when it is used in a manner that is inconsistent to published user or operator instructions and/or installation instructions.	31
2. Service calls to correct the installation of your major appliance, to instruct you on how to use your major appliance, to replace or repair house fuses, or to correct house wiring or plumbing.	31
3. Service calls to repair or replace appliance light bulbs, air filters or water filters. Consumable parts are excluded from warranty coverage.	31
4. Damage resulting from accident, alteration, misuse, abuse, fire, flood, acts of God, improper installation, installation not in accordance with electrical or plumbing codes, or use of products not approved by Maytag.	31
5. Cosmetic damage, including scratches, dents, chips or other damage to the finish of your major appliance, unless such damage results from defects in materials or workmanship and is reported to Maytag within 30 days from the date of purchase.	31
6. Pick up and delivery. This major appliance is intended to be repaired in your home.	31
7. Repairs to parts or systems resulting from unauthorized modifications made to the appliance.	31
8. Expenses for travel and transportation for product service if your major appliance is located in a remote area where service by an authorized Maytag servicer is not available.	31
9. The removal and reinstallation of your major appliance if it is installed in an inaccessible location or is not installed in accordance with Maytag’s published installation instructions.	31
10. Replacement parts or repair labor on major appliances with original model/serial numbers that have been removed, altered, or cannot be easily determined.	31
DISCLAIMER OF IMPLIED WARRANTIES	31
IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW. Some states and provinces do not allow limitations on the du...	31
LIMITATION OF REMEDIES; EXCLUSION OF INCIDENTAL AND CONSEQUENTIAL DAMAGES	31
YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN. MAYTAG SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states and provinces do not allow the exclusion or limitation of incidenta...	31
If outside the 50 United States and Canada, contact your authorized Maytag dealer to determine if another warranty applies.	31
If you think you need repair service, first see the “Troubleshooting” section of the Use & Care Guide. If you are unable to resolve the problem after checking “Troubleshooting,” additional help can be found by checking the “Assistance or Se...	31
SÉCURITÉ DE LA LAVEUSE	32
Exigences d'installation	34
Outillage et pièces	34
Outils nécessaires au raccordement des tuyaux d'arrivée d'eau	34
Outils nécessaires pour le raccordement du tuyau de vidange	34
Outils nécessaires à l'installation	34
Autres pièces	34
Options	34
Piédestal	34
Piédestal facultatif	34
Ensemble de superposition	35
Exigences d'emplacement	35
Dégagements de séparation à respecter	35
Dimensions de la laveuse	35
Espacement recommandé pour une installation personnalisée sous un comptoir	35
Espacement recommandé pour une installation dans un encastrement ou dans un placard, avec ou sans piédestal	35
Espacement recommandé pour une installation dans un encastrement ou dans un placard, avec laveuse et sécheuse superposées	36
Espacement recommandé pour l’installation dans un placard	37
Système de vidange	37
Système de vidange avec tuyau de rejet à l'égout - mural ou au plancher (vues A et B)	37
Système de vidange avec évier de buanderie (vue C)	37
Système de vidange au plancher (vue D)	37
Spécifications électriques	37
Instructions d'installation	38
Élimination des accessoires de transport	38
1. Au moyen d'une clé de 13 mm, desserrer chacun des boulons.	38
2. Une fois le boulon desserré, le déplacer au centre du trou et retirer complètement le boulon, y compris la cale d'espacement en plastique couvrant le boulon.	38
3. Une fois que les 4 boulons ont été retirés, jeter les boulons et les cales d'espacement. Puis tirer le cordon d'alimentation à travers l'ouverture du panneau arrière et obturer le trou avec le bouchon fourni.	38
4. Obturer les trous des boulons avec les 4 bouchons pour les trous des boulons de transport.	39
Raccordement des tuyaux d'alimentation	39
Connecter les tuyaux d'alimentation aux robinets d'eau	39
1. Fixer un tuyau au robinet d'eau chaude. Visser complètement le raccord à la main pour qu'il comprime le joint.	39
2. Fixer un tuyau au robinet d'eau froide. Visser complètement le raccord à la main pour qu'il comprime le joint.	39
3. À l'aide d'une pince, serrer les raccords en effectuant deux tiers de tour supplémentaires.	39
Purger les canalisations d'eau	39
Connecter les tuyaux d'alimentation à la laveuse	39
1. Fixer le tuyau d'eau chaude à la valve du tuyau d'alimentation d'eau chaude (H) de la laveuse. Visser complètement le raccord à la main pour qu'il comprime le joint.	39
2. Fixer le tuyau d'eau froide au robinet d'eau froide (C) de la laveuse. Visser complètement le raccord à la main pour qu'il comprime le joint.	39
3. À l'aide d'une pince, serrer les raccords en effectuant 2/3 de tour supplémentaires.	39
4. Ouvrir les robinets d'eau complètement et vérifier s'il y a des fuites.	39
Raccordement du tuyau de vidange	40
1. À l'aide d'une pince multiprise, serrer les deux onglets de la bride de tuyau et insérer la bride sur l'extrémité du tuyau de vidange.	40
2. Faire glisser le tuyau de vidange sur le raccord de la laveuse.	40
3. Une fois le tuyau de vidange en place, relâcher la prise de la pince.	40
4. Le système de vidange de la laveuse peut être installé à l'aide d'un conduit d'évacuation au plancher, un tuyau de rejet à l'égout rigide au mur ou au plancher ou un évier de buanderie.	40
Égout au plancher	40
Immobilisation du tuyau de vidange	41
1. Faire passer le cordon d'alimentation par-dessus la laveuse.	41
2. Déplacer la laveuse à son emplacement final.	41
3. Placer le tuyau de vidange dans l'évier de buanderie ou le tuyau de rejet à l'égout. Voir les illustrations A et B.	41
4. Si les robinets d'eau et le tuyau rigide de rejet à l'égout sont placés en retrait, introduire l'extrémité en crochet du tuyau de vidange dans le tuyau rigide de rejet à l'égout, tel qu'indiqué. Voir l'illustration C.	41
Réglage de l'aplomb de la laveuse	41
1. Faire glisser la laveuse à son emplacement final.	41
2. S’assurer que les quatre pieds sont bien en contact avec le plancher.	41
3. Utiliser un niveau placé sur le bord supérieur de la laveuse pour contrôler l’aplomb, d'abord transversalement, puis dans le sens avant arrière.	41
4. Vérifier que les quatre pieds sont stables et reposent sur le plancher. Vérifier ensuite que la laveuse est parfaitement d’aplomb (utiliser un niveau). Répéter les étapes 1 à 3 jusqu’à ce que la laveuse soit d’aplomb.	41
5. Après que l’aplomb de la laveuse a été établi et que les quatre pieds sont bien en contact avec le plancher, tourner les écrous de blocage sur les pieds à l’aide d'une clé à molette de 9/16\	41
6. La laveuse ne doit pas bouger d’avant en arrière, latéralement ou transversalement lorsqu’on appuie sur les bords supérieurs.	41
7. Vérifier le bon aplomb de la laveuse.	41
Achever l'installation	42
1. Consulter les spécifications électriques. Vérifier que la tension électrique disponible est correcte et que la prise de courant est convenablement reliée à la terre. Voir “Spécifications électriques”.	42
2. Vérifier que toutes les pièces sont maintenant installées. S'il reste une pièce, passer en revue les différentes étapes pour découvrir laquelle aurait été oubliée.	42
3. S'assurer d'avoir récupéré tous vos outils.	42
4. Jeter ou recycler tous les matériaux d'emballage.	42
5. Vérifier que chaque robinet d'arrivée d'eau est ouvert.	42
6. Vérifier s'il y a des fuites autour des robinets et des tuyaux d'arrivée d'eau.	42
7. Brancher sur une prise à 3 alvéoles reliée à la terre.	42
8. Lire “Utilisation de la laveuse”.	42
9. Pour tester le fonctionnement de la machine et la nettoyer, mesurer la moitié de la quantité de détergent HE Haute Efficacité recommandée par le fabricant pour une charge de taille moyenne. Verser le détergent dans le distributeur. Sélectio...	42
Utiliser uniquement un détergent HE Haute efficacité.	42
CARACTÉRISTIQUES ET AVANTAGES	43
Commandes électroniques	43
Niveau d'eau automatique	43
Volume de charge plus important	43
Système de suspension	43
Tambour en acier inoxydable	43
Moteur adaptatif à vitesse variable	43
Vitesses d'essorage	43
Optimiseur thermique	43
Certifié pour aseptiser	43
Add A Garment (ajouter un vêtement)	43
Équilibre dynamique	43
Système supérieur de distribution de détergent	43
Utiliser uniquement un détergent HE Haute efficacité.	43
UTILISATION DE LA LAVEUSE	44
REMARQUE : Le tableau de commande de votre modèle peut différer de celui illustré ci-dessus.	44
Mise en marche de la laveuse	44
Utilisation du détergent approprié	44
Utiliser uniquement un détergent HE Haute efficacité.	44
Premier programme de lavage sans linge à laver	44
Pour tous les programmes de lavage	45
1. Pour charger la laveuse Ouvrir la porte de la laveuse en tirant sur la poignée. Trier le linge d'après la couleur et le type de tissu. Placer une charge de linge trié dans la laveuse. Ne pas surcharger la laveuse. Une surcharge peut causer un n...	45
2. Fermer la porte de la laveuse en la poussant fermement jusqu'à ce que le verrou s'enclenche. La porte de la laveuse demeurera verrouillée durant le programme de lavage.	45
3. Ouvrir le tiroir distributeur et verser les produits de lessive dans les compartiments de détergent, d'agent de blanchiment ou d'assouplissant de tissu. Fermer le tiroir lentement pour éviter les renversements. Voir “Utilisation du distributeu...	45
4. Mettre la laveuse en marche en sélectionnant POWER (alimentation). Sélectionner un des programmes en tournant le sélecteur de programme. Le témoin lumineux correspondant au programme sélectionné s'allumera. Lors de la sélection d'un program...	45
5. Sélectionner les OPTIONS désirées telles que Prewash (prélavage), MAX EXTRACT™, Stain Cycle (programme contre les taches) ou Extra Rinse (rinçage supplémentaire). Toutes les options ne sont pas disponibles avec tous les programmes. Voir ...	45
6. Sélectionner les MODIFICATEURS désirés, tels que Spin Speed (vitesse d'essorage) et Wash/Rinse Temp (température de lavage/rinçage). Tous les modificateurs ne sont pas disponibles avec tous les programmes et toutes les options. Voir “Modifi...	45
7. Si désiré, sélectionner le CYCLE SIGNAL (signal de programme). Le signal est utile lorsque vous lavez des articles qui doivent être enlevés de la laveuse aussitôt qu'elle s'arrête. Appuyer une fois sur CYCLE SIGNAL (signal de programme) pou...	45
8. Pour commencer le programme de lavage immédiatement Sélectionner START (pendant 1 seconde environ).	45
9. Pour commencer le programme de lavage ultérieurement Sélectionner DELAY WASH (lavage différé) jusqu'à ce que la durée souhaitée (en heures) apparaisse sur l'afficheur de la durée résiduelle estimée. Sélectionner START (mise en marche). ...	45
Utilisation du distributeur	45
Choix du détergent approprié	45
Utiliser uniquement un détergent HE Haute efficacité.	45
Pour remplir les compartiments du distributeur	45
1. Tirer le tiroir distributeur.	45
2. Ajouter le produit de lessive désiré dans le compartiment approprié.	45
3. Enfoncer le tiroir distributeur lentement et complètement (pour éviter les renversements).	46
Distributeur	46
Compartiment pour détergent du lavage principal	46
Compartiment de l'agent de blanchiment	46
Compartiment pour assouplissant de tissu	46
Pause et remise en marche	46
1. Pour faire faire une pause à la laveuse à tout moment, sélectionner PAUSE/CANCEL (pause/annulation).	46
2. Pour poursuivre le programme, sélectionner START (pendant environ 1 seconde).	46
Changement des programmes, options et modificateurs	46
Pour arrêter un programme et en sélectionner un autre	46
1. Sélectionner deux fois PAUSE/CANCEL (pause/annulation).	46
2. Sélectionner POWER (alimentation).	46
3. Sélectionner le programme désiré.	46
4. Sélectionner les OPTIONS désirées, telles que Prewash (prélavage), MAX EXTRACT™, Stain Cycle (programme contre les taches) ou Extra Rinse (rinçage supplémentaire).	46
5. Sélectionner les MODIFICATEURS désirés, tels que Spin Speed (vitesse d'essorage) ou Wash/Rinse Temp (température de lavage/rinçage).	46
6. Sélectionner START (pendant environ 1 seconde) pour remettre la laveuse en marche au début du nouveau programme.	46
Pour annuler un programme	46
1. Sélectionner deux fois PAUSE/CANCEL (pause/annulation).	46
2. La laveuse s'éteint, la porte se déverrouille et les vêtements peuvent être retirés.	46
Pour changer les options ou les modificateurs lorsque le programme a commencé	46
1. Sélectionner PAUSE/CANCEL (pause/annulation).	46
2. Sélectionner les Spin Speed (vitesse d’essorage), Wash/Rinse Temp (température de lavage/rinçage) ou OPTIONS désirées (telles que Prewash [prélavage], MAX EXTRACT™, Stain Cycle [programme contre les taches] ou Extra Rinse [rinçage suppl...	46
3. Appuyer sur la touche START (pendant environ 1 seconde) pour poursuivre le programme.	47
Pour vidanger la laveuse manuellement	47
1. Sélectionner PAUSE/CANCEL (pause/annulation).	47
2. Sélectionner SPIN Only (essorage seulement).	47
3. Sélectionner START (pendant environ 1 seconde) pour commencer la vidange.	47
4. Lorsque l'essorage est terminé, la porte se déverrouille. Les articles peuvent être retirés de la laveuse.	47
Témoins lumineux	47
Ajout d'articles	47
1. Sélectionner PAUSE/CANCEL (pause/annulation). La porte de la laveuse se déverrouille et les articles peuvent être ajoutés.	47
2. Pour poursuivre le programme, fermer la porte et sélectionner START (pendant environ 1 seconde).	47
Clean (propre)	47
Verrouillage des commandes	47
Durée résiduelle estimée	47
Door Locked (porte verrouillée)	47
Programmes	48
Programmes de lavage	48
Préréglages de programme	48
Programme	48

Match case Limit results 1 per page

Location Requirements

Selecting the proper location for your washer improves performance and minimizes noise and

possible washer “walk.”

Your washer can be installed under a custom counter, or in a basement, laundry room, closet,

or recessed area. See “Drain System.”

Companion appliance location requirements should also be considered. Proper installation is

your responsibility.

You will need

A water heater set to deliver 120°F (49°C) water to the washer.

A grounded electrical outlet located within 6 ft (1.8 m) of where the power cord is

attached to the back of the washer. See “Electrical Requirements.”

Hot and cold water faucets located within 4 ft (1.2 m) of the hot and cold water fill valves,

and water pressure of 20-100 psi (137.9-689.6 kPa).

A level floor with a maximum slope of 1" (25 mm) under entire washer. Installing the

washer on soft floor surfaces, such as carpets or surfaces with foam backing, is not

recommended.

A sturdy and solid floor to support the washer with a total weight (water and load) of

400 lbs (180 kg).

Do not operate your washer in temperatures below 32°F (0°C). Some water can remain in the

washer and can cause damage in low temperatures. See “Washer Care” for information on

winterizing.

Installation clearances

The location must be large enough to allow the washer door to be fully opened.

Additional spacing should be considered for ease of installation and servicing. The door

opens more than 90°, and it is not reversible.

Additional clearances might be required for wall, door, and floor moldings.

Additional spacing of 1" (25 mm) on all sides of the washer is recommended to reduce

noise transfer.

Companion appliance spacing should also be considered.

Washer Dimensions

27"

(686 mm)

50¼"

(1276 mm)

36"

(914 mm)

30½"

(775 mm)

Door is not reversible.

Recommended installation spacing for custom undercounter installation

The dimensions shown are for the recommended spacing.

Custom undercounter installation - Washer only

(25 mm)

37" min.

(939 mm)

27"

(686 mm)

Recommended installation spacing for recessed or closet installation, with or without

a pedestal

The dimensions shown are for the recommended spacing.