Maytag MVWB880BW Use & Care Guide - Page 14

To remove suds, cancel cycle. Select RINSE/DRAIN & SPIN. Select

Get Maytag MVWB880BW PDF manuals and user guides View all Maytag MVWB880BW manuals
Add to My Manuals
Save this manual to your list of manuals

Page 14 highlights

TROUBLESHOOTING First try the solutions suggested here or visit our website to possibly avoid the cost of a service call. In U.S.A. www.maytag.com/product_help - In Canada www.maytag.ca. If you experience Possible Causes Solution Washer not performing as expected (cont.) Washer won't run or fill, washer stops working (cont.) Check proper electrical supply. Plug power cord into a grounded 3-prong outlet. Do not use an extension cord. Ensure there is power to outlet. Reset a tripped circuit breaker. Replace any blown fuses. NOTE: If problems continue, contact an electrician. Normal washer operation. Lid must be closed for washer to run. Washer will pause during certain phases of cycle. Do not interrupt cycle. Washer may be stopped to reduce suds. Washer may be tightly packed. Remove several items, rearrange load evenly around the washplate. Do not load garments directly over the center of the wash plate. Close lid and press START/PAUSE. Add only 1 or 2 additional garments after washer has started. Do not add more water to the washer. Not using HE detergent or using too much HE detergent. Only use HE detergent. Suds from regular detergents can slow or stop the washer. Always measure detergent and following detergent directions based on your load requirements. To remove suds, cancel cycle. Select RINSE/DRAIN & SPIN. Select your cycle. Press START/PAUSE. Do not add more detergent. Washer not draining/ spinning, loads are still wet Empty pockets and use garment bags for small items. Using cycles with a lower spin speed. Small items may have been caught in pump or between basket and tub, which can slow draining. Cycles with lower spin speeds remove less water than cycles with high spin speeds. Use the recommended cycle/speed spin for your garment. Washer may be tightly packed or unbalanced. Tightly packed loads may not allow the washer to spin correctly, leaving the load wetter than normal. Evenly arrange the wet load for balanced spinning. Select RINSE/DRAIN & SPIN to remove excess water. See "Using Your Washer" for loading recommendations. Check plumbing for correct drain hose installation. Drain hose extends into standpipe farther than 4.5" (114 mm). Check drain hose for proper installation. Use drain hose form and securely attach to drainpipe or tub. Do not tape over drain opening. Lower drain hose if the end is higher than 96" (2.4 m) above the floor. Remove any clogs from drain hose. 14

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
14
TROUBLESHOOTING
If you experience
Possible Causes
Solution
Washer not performing as expected (cont.)
Washer won’t run
or fill, washer stops
working (cont.)
Check proper electrical supply.
Plug power cord into a grounded 3-prong outlet.
Do not use an extension cord.
Ensure there is power to outlet.
Reset a tripped circuit breaker. Replace any blown fuses.
NOTE:
If problems continue, contact an electrician.
Normal washer operation.
Lid must be closed for washer to run.
Washer will pause during certain phases of cycle.
Do not interrupt cycle.
Washer may be stopped to reduce suds.
Washer may be tightly packed.
Remove several items, rearrange load evenly around the
washplate. Do not load garments directly over the center
of the wash plate. Close lid and press START/PAUSE.
Add only 1 or 2 additional garments after washer has started.
Do not add more water to the washer.
Not using HE detergent or using too
much HE detergent.
Only use HE detergent. Suds from regular detergents can slow or
stop the washer. Always measure detergent and following detergent
directions based on your load requirements.
To remove suds, cancel cycle. Select RINSE/DRAIN & SPIN. Select
your cycle. Press START/PAUSE. Do not add more detergent.
Washer not draining/
spinning, loads are
still wet
Empty pockets and use garment bags
for small items.
Small items may have been caught in pump or between basket and
tub, which can slow draining.
Using cycles with a lower spin speed.
Cycles with lower spin speeds remove less water than cycles with
high spin speeds. Use the recommended cycle/speed spin for your
garment.
Washer may be tightly packed or
unbalanced.
Tightly packed loads may not allow the washer to spin correctly,
leaving the load wetter than normal. Evenly arrange the wet load for
balanced spinning. Select RINSE/DRAIN & SPIN to remove excess
water. See “Using Your Washer” for loading recommendations.
Check plumbing for correct drain
hose installation. Drain hose extends into
standpipe farther than 4.5” (114 mm).
Check drain hose for proper installation. Use drain hose form and
securely attach to drainpipe or tub. Do not tape over drain opening.
Lower drain hose if the end is higher than 96” (2.4 m) above the floor.
Remove any clogs from drain hose.
First try the solutions suggested here or visit our website to possibly avoid the cost of a service call.
In U.S.A. www.maytag.com/product_help – In Canada www.maytag.ca.