Maytag MVWC700VW Installation Instructions - Page 3

Selecting the proper location for your washer improves

performance

and minimizes

noise and possible washer "walk".

Your washer can be installed in a basement,

laundry room, closet,

or recessed area. See "Drain System."

IMPORTANT:

Do not install or store the washer where it will be

exposed to the weather.

Proper installation

is your responsibility.

You

will

need:

m

A water heater set to deliver 120°F (49°C) water to the washer.

m

A grounded

electrical

outlet located within 4 ft (1.2 m) of

where the power cord is attached to the back of the washer.

See "Electrical

Requirements."

m

Hot and cold water faucets

located within 3 ft (90 cm) of the

hot and cold water fill valves, and water pressure of 5-100 psi

(34.5-690 kPa). Washers with triple dispensers

require

20-100

psi (138-690

kPa) for best performance.

m

A level floor with a maximum

slope of 1" (2.5 cm) under

entire washer. Installing the washer on carpeting

is not

recommended.

m

A sturdy floor to support

the washer weight

(washer, water,

and load) of 315 Ibs (143 kgs).

Do not store or operate

your washer in temperatures

at or below

32°F (0°C). Some water can remain in the washer and can cause

damage

in tow temperatures.

See "Washer Care" in the Washer

User Instructions

for winterizing

information.

Recessed

area

or

closet

installation

The dimensions

shown

are for the recommended

spacing allowed

(A and B), except the closet door ventilation

openings.

The

dimensions

shown

for the closet door ventilation

openings

(C)

are the minimum required.

m

0"

_1 6-

_" _1 6-

0"

_"

_25,_'_q

_!

_"

max.

IF-----3

_._0al

(310_

241n.

_

__

I

__g.6

ca)

|

(_o2

_)

A

B

C

A. Front view

B. Side view

C. Closet door with vents

m

Additional

spacing

should be considered

for ease

of installation

and servicing.

m

Additional

clearances

may be required for wall, door,

and floor moldings.

m

Additional

spacing

of 1" (2.5 cm) on all sides of the washer

is recommended

to reduce noise transfer.

m

If a closet door is installed, the minimum air openings

in the

top and bottom of the door are required (C). Louvered doors

with air openings

in the top and bottom

are acceptable.

Companion

appliance spacing

should also be considered.

The washer can be installed using the standpipe

drain system

(floor or wall), the laundry tub drain system, or the floor drain

system. Select the drain hose installation

method you need.

See "Tools and Parts."

Standpipe

drain

system--wall

or floor

(views

A&

B)

i

,i

The standpipe

drain requires a minimum diameter

standpipe

of

2" (5 cm). The minimum

carry-away

capacity

can be no less than

17 gal. (64 L) per minute. A I_A" (3.2 cm) diameter

to 1" (2.5 cm)

diameter

standpipe

adapter

kit is available.


The top of the standpipe

must be at least 39" (99 cm) high

and no higher than 96" (244 cm) from the bottom of the washer.

IMPORTANT:

To avoid siphoning,

no more than 8" (20.3 cm) of

drain hose should be inside the standpipe. See "Connect drain hose."

Laundry

tub drain

system

(view C)

The laundry tub needs a minimum

20 gal. (76 L) capacity. The top

of the laundry tub must be at least 39" (99 cm) above the floor and

no higher than 96" (244 cm) from the bottom of the washer.

Floor

drain

system (view D)

The floor drain system requires a siphon break that may be

purchased

separately.


The siphon break must be a minimum of 28" (71 cm) from the

bottom

of the washer. Additional

hoses might be needed.

To avoid siphoning,

no more than 8" (20.3 cm) of drain hose

should be below the top of the wash tub. Secure drain hose

with beaded tie strap.

(7t

crn)

C

Maytag MVWC700VW Installation Instructions - Page 3

See Washer Care in the Washer - dimensions

Page 3 highlights