Metabo WPB 13-125 Quick DS Operating Instructions - Page 10

en ENGLISH f) Use extra caution when making a "pocket cut" into existing walls or other blind areas. The protruding wheel may cut gas or water pipes, electrical wiring or objects that can cause kickback. 3.5 Safety Warnings Specific for Sanding Operations: a) Do not use excessively oversized sanding disc paper. Follow manufacturer's recommendations when selecting sanding paper. Larger sanding paper extending beyond the sanding pad presents a laceration hazard and may cause snagging, tearing of the disc or kickback. 3.6 Only for WEVA 15-125 Quick: Safety Warnings Specific for Polishing Operations: a) Do not allow any loose portion of the polishing bonnet or its attachment strings to spin freely. Tuck away or trim any loose attachment strings. Loose and spinning attachment strings can entangle your fingers or snag on the workpiece. 3.7 Safety Warnings Specific for Wire Brushing Operations: a) Be aware that wire bristles are thrown by the brush even during ordinary operation. Do not overstress the wires by applying excessive load to the brush. The wire bristles can easily penetrate light clothing and/or skin. b) If the use of a guard is recommended for wire brushing, do not allow any interference of the wire wheel or brush with the guard. Wire wheel or brush may expand in diameter due to work load and centrifugal forces. 3.8 Additional safety instructions: WARNING - Always wear protective goggles. Use only accessories that are covered by at least 3.4 mm by the safety guard. Use elastic cushioning layers if they have been supplied with the grinding media and if required. Observe the specifications of the tool or accessory manufacturer! Protect the discs from grease or impacts! Grinding discs must be stored and handled with care in accordance with the manufacturer's instructions. Never use cutting discs for roughing work! Do not apply pressure to the side of the cutting discs. The workpiece must lay flat and be secured against slipping, e.g. using clamps. Large workpieces must be sufficiently supported. If accessories with threaded inserts are used, the end of the spindle may not touch the base of the hole on the grinding tool. Make sure that the thread 10 in the accessory is long enough to accommodate the full length of the spindle. The thread in the accessory must match the thread on the spindle. See page 4 and chapter 13. Technical Specifications for more information on the spindle length and thread. The use of a fixed extractor system is recommended. Always install an RCD with a maximum trip current of 30 mA upstream. If the angle grinder is shut down via the RCD, it must be checked and cleaned. See chapter 8. Cleaning. Damaged, eccentric or vibrating tools may not be used. Avoid damage to gas or water pipes, electrical cables and load-bearing walls (static). Pull the plug out of the socket before making any adjustments, converting or servicing the machine. Metabo S-automatic safety clutch. When the safety clutch responds, switch off the machine immediately! A damaged or cracked additional handle must be replaced. Never operate a machine with a defective additional handle. A damaged or cracked safety guard must be replaced. Never operate a machine with a defective safety guard. Secure small workpieces. For example, clamp in a vice. Additional Warnings:California Prop 65 08_2018 WARNING Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: • Lead from lead-based paints, • Crystalline silica from bricks and cement and other masonry products, and • Arsenic and chromium from chemicallytreated lumber. Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles. WPB 13-150 Quick DS, WEPBA 17-125 Quick DS, WEPBA 17-125 Quick RT DS, WEPBA 17-150 Quick DS, WEPBA 17-150 Quick RT DS, WEPB 17-125 Quick DS, WEPB 17-150 Quick DS, WEPB 19-180 RT DS: Metal eye for protection against falling (Does not apply to WEPBA 17125 Quick, WEPBA 17-150 Quick.) WPB 12-150 Quick DS, WEPBA 17-125 Quick DS, WEPBA 17-125 Quick RT DS, WEPBA 17-150 Quick DS, WEPBA 17-150 Quick RT DS, WEPB 17125 Quick DS, WEPB 17-150 Quick DS, WEPB 19180 RT DS is equipped with a metal eye for protection against falling.