Metabo WPB 13-125 Quick DS Operating Instructions - Page 14
Accessories, Repairs, Environmental protection, Technical specifications
View all Metabo WPB 13-125 Quick DS manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 14 highlights
en ENGLISH Machines with VTC, TC and VC electronics: The electronic signal display (7) flashes and the machine does not start. The restart protection is active. If the plug is put into the socket with the machine switched on, or if the power supply is restored following an interruption, the machine will not start up. Switch the machine off and back on again. 10. Accessories Use only original Metabo accessories. See page 5. Use only accessories which fulfil the requirements and specifications listed in these operating instructions. A Special safety guard for "hubbed wheels" For use with "hubbed wheels". The safety guard must overlap accessories by at least 3.4 mm. B Cutting guard clip / guard for cut-off grinding Designed for work with cutting disc and diamond cutting discs. Once the cutting guard clip is fitted, the safety guard becomes a cutting guard. C Extraction guard for cut-off grinding Designed for cutting through stone slabs with diamond cutting discs. With nozzle for extracting stone dust using a suitable extraction unit. D Extraction guard for surface grinding Intended for grinding of concrete, screed, wood and plastics with diamond cup wheels and/or fibre discs and suitable sanding plates. With nozzle for extracting stone, wood and plastic dust using a suitable extraction unit. Not suitable for extracting sparks or for grinding of metals. E Dust filter The fine mesh filter prevents coarse particles from entering the motor housing. Remove regularly and clean. F Hand protection Intended for work with backing pads, sanding plates, wire brushes and support plates, sanding pads, wire brushes and diamond Drill Bits for tiles. Install hand guard under the additional sidemounted handle. G Multiple position bar for side handle Permits numerous handle positions. H Bar side handle For a complete range of accessories, see www.metabo.com or the accessories catalogue. 11. Repairs Repairs to electrical tools must be carried out by qualified electricians ONLY! If the connection lead is damaged, it must be replaced by a special connection lead. Contact your local Metabo representative if you have Metabo power tools that need repairing. You can find the addresses on www.metabo.com. 14 You can download a list of spare parts from www.metabo.com. 12. Environmental protection The generated grinding dust may contain harmful substances. Dispose appropriately. Observe national regulations regarding environmentally compatible disposal and the recycling of old machines, packaging and accessories. 13. Technical specifications Explanatory notes on the specifications on page 4. Changes due to technological progress reserved. Ø = max. diameter of the accessory tmax,1 = max. permitted thickness of the clamping shank on accessory when using 2-hole nut (15) tmax,2=max. permitted thickness of clamping shank on accessory when using "Quick" clamping nut (1) tmax,3 = roughing disc/cutting disc: max. permitted thickness of accessory M = spindle thread l = length of the grinding spindle n* = no-load speed (maximum speed) Inm1V2*0 V = no-load speed (adjustable) = Current at 120 V = weight without mains cable * Machines with the designation WE... : Energy-rich, high-frequency interference can cause fluctuations in speed. The fluctuations disappear, however, as soon as the interference fades away. The technical specifications quoted are subject to tolerances (in compliance with the relevant valid standards). Emission values These values make it possible to assess the emissions from the power tool and to compare different power tools. Depending on the operating conditions, the condition of the power tool or the accessories, the actual load may be higher or lower. For assessment purposes, please allow for breaks and periods when the load is lower. Based on the adjusted estimates, arrange protective measures for the user e.g. organisational measures. Vibration total value (vector sum of three directions) determined in accordance with EN 60745: ah, SG = Vibration emission value (surface grinding) ah, DS = Vibration emission value (sanding with sanding plate) ah, P = Vibration emission value (polishing) Kh,SG/DS/P = Uncertainty (vibration) Wear ear protectors!