NEC 60XM5 User Manual - Page 35

Information Ⅵ AUTO ID settings ON: Enables Auto ID function. In the case shown below, display 1 will be set as ID 1, display 2 as ID2, etc. This can be set only when a 2‫ן‬2, 3‫ן‬3, 1‫ן‬5 or 5‫ן‬1 is selected. REMOTE IN No.1 No.2 No.4 No.3 Display 1 REMOTE OUT REMOTE IN No.1 No.2 No.4 No.3 Display 2 REMOTE OUT REMOTE OUT No.1 No.2 No.4 No.3 Display 4 REMOTE OUT REMOTE IN No.1 No.2 No.4 No.3 REMOTE IN Display 3 OFF: Disables Auto ID function. Note: To use this function, you have to connect the displays with the remote cable (not supplied). control the No.1 monitor will turn on and the others will be turned on one by one automatically. * From the second monitor onward, neither the POWER button on the unit nor the POWER ON button on the remote control works. However, by pressing and holding the POWER ON button for more than 3 seconds, the monitor will be turned on. OFF: Turns on the main power of all displays at the same time. (Only for 4‫ן‬4 and 5‫ן‬5 video wall modes) MODE1: Turns on the main power of each display delayed. MODE2: Turns on the main power of each display more delayed. OFF: Turns on the main power of all displays at the same time. Note: To use this function, you have to connect the displays with the remote cable (not supplied). IMAGE ADJUST The position of the image can be adjusted and flickering of the image can be corrected. Example: Adjusting the vertical position PLE LINK Use this function to set a uniform brightness for each display. Turn on the AUTO ID and set the DIVIDER (at 1, 2‫ן‬2, 3‫ן‬3, 1‫ן‬5 or 5‫ן‬1) before the following operations. On "VIDEO WALL" menu, select "IMAGE ADJUST", then Example: Setting "ON" press the MENU/ENTER button. The "IMAGE ADJUST" screen appears. On "V-POSITION" of "IMAGE ADJUST" menu, adjust the position. IMAGE ADJUST ASPECT MODE : NORMAL V- P O S I T I O N H-POSITION V- H E I G H T H-WIDTH AUTO PICTURE : OFF FINE PICTURE PICTURE ADJ. UNDERSCAN : OFF SEL. ADJ. EXIT RETURN : ±0 : ±0 : 0 : 0 : 0 : 0 V-POSITION : +64 On "PLE LINK" of "VIDEO WALL" menu, select "ON", then press the MENU/ENTER button. VIDEO WALL DIVIDER : 1 POSITION DISP. MODE : SPLIT AUTO ID : OFF IMAGE ADJUST P. ON DELAY : OFF PLE LINK : ON SEL. ADJ. EXIT RETURN Information Information Ⅵ IMAGE ADJUST settings These are the same functions as the IMAGE ADJUST menu on page En-23. Ⅵ PLE LINK settings ON: Sets a uniform brightness for each screen in a video wall. This can be set only when a 1, 2‫ן‬2, 3‫ן‬3, 1‫ן‬5 or 5‫ן‬1 video wall is selected. OFF: Sets the individual screen brightness for each P. ON DELAY (Power on delay) screen in a video wall. Use this function to activate power-on delay. * When this function is set "ON", connect your plasma Turn on the AUTO ID before the following operations. Example: Setting "ON" On "P. ON DELAY" of "VIDEO WALL" menu, select "ON". displays with the remote cable (optional) in the order of the position numbers for the 2‫ן‬2 video wall. See the drawing below. * If there are changes in the DIVIDER or POSITION, the PLE LINK will automatically turn OFF. VIDEO WALL DIVIDER : 1 POSITION DISP. MODE : SPLIT AUTO ID : OFF IMAGE ADJUST P. ON DELAY : ON PLE LINK : OFF REMOTE IN No.1 No.2 No.4 No.3 Display 1 REMOTE OUT REMOTE IN No.1 No.2 No.4 No.3 Display 2 REMOTE OUT SEL. ADJ. Information EXIT RETURN REMOTE OUT No.1 No.2 No.4 No.3 Display 4 REMOTE OUT REMOTE IN No.1 No.2 No.4 No.3 REMOTE IN Display 3 Ⅵ P. ON DELAY settings * With the 3‫ן‬3, 1‫ן‬5 or 5‫ן‬1 video wall, connect the (Video wall modes other than 4‫ן‬4 and 5‫ן‬5) ON: Turns on the main power of each display after a delay time. final display to the first display the same way as with 2‫ן‬2 video wall. Note: * Once this function has been set to "ON", POWER ON/ * The remote control can be operated unless the IR OFF button on the remote control does not function REMOTE is set to "OFF". except for the No.1 monitor. * To use this function, you have to connect the displays By pressing the POWER ON button on the remote En-34 with the remote cable (not supplied).