NEC LT265 LT245/265 UM - Page 36

Use the SELECT

Get NEC LT265 - XGA DLP Projector PDF manuals and user guides
UPC - 050927247354
View all NEC LT265 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 36 highlights

3. Projecting an Image (Basic Operation) Note on Startup screen (Menu Language Select screen) When you first turn on the projector, you will get the Startup menu. This menu gives you the opportunity to select one of the 21 menu languages. To select a menu language, follow these steps: 1. Use the SELECT ̆ or ̄ button to select one of the 21 languages for the menu. MENU SELECT ENTER PC CARD EXIT SOURCE AUTO ADJUST 3D REFORM ON/STAND BY LAMP STATUS POWER OFF MAGNIFY POWER LASER POINTER ON PAGE UP DOWN MENU ENTER EXIT R-CLICK 2. Press the ENTER button to execute the selection. MENU SELECT ENTER EXIT PC CARD SOURCE AUTO ADJUST 3D REFORM ON/STAND BY LAMP STATUS POWER OFF MAGNIFY POWER LASER POINTER ON PAGE UP DOWN MENU ENTER EXIT 3. To close the menu, press the EXIT button. NOTE: Immediately after turning on the projector and displaying an image, you cannot turn off the projector for 60 seconds. After this has been done, you can proceed to the menu operation. If you want, you can select the menu language later. See "Language" on page 91. MENU SELECT ENTER EXIT PC CARD SOURCE AUTO ADJUST 3D REFORM ON/STAND BY LAMP STATUS POWER R-CLICK OFF MAGNIFY POWER LASER POINTER ON PAGE UP DOWN MENU ENTER R-CLICK EXIT NOTE: Immediately after turning on the projector, screen flicker may occur. This is not a fault. Wait 3 to 5 minutes until the lamp lighting is stabilized. When the Lamp mode is set to Eco, the Lamp indicator will light green. If one of the following things happens, the projector will not turn on. • If the internal temperature of the projector is too high, the projector detects abnormal high temperature. In this condition the projector will not turn on to protect the internal system. If this happens, wait for the projector's internal components to cool down. • When the lamp reaches its end of usable life, the projector will not turn on. If this happens, replace the lamp. See page 119. • If the lamp fails to light, and if the STATUS indicator flashes on and off in a cycle of six times, wait a full minute and then turn on the power. 29

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
29
PC CARD
SOURCE
AUTO ADJUST
3D REFORM
LAMP
STATUS
POWER
ON/STAND BY
E
N
T
E
R
E
X
I
T
M
E
N
U
SELECT
POINTER
LASER
MAGNIFY
PAGE
OFF
POWER
ON
E
N
T
E
R
M
E
N
U
E
X
I
T
R
-
C
L
I
C
K
UP
DOWN
PC CARD
SOURCE
AUTO ADJUST
3D REFORM
LAMP
STATUS
POWER
ON/STAND BY
E
N
T
E
R
E
X
I
T
M
E
N
U
SELECT
3. Projecting an Image (Basic Operation)
Note on Startup screen (Menu Language Select screen)
When you first turn on the projector, you will get the Startup menu. This menu gives you the opportunity to select one
of the 21 menu languages.
To select a menu language, follow these steps:
1.
Use the SELECT
±
or
²
button to select one of the
21 languages for the menu.
2.
Press the ENTER button to execute the selection.
NOTE: Immediately after turning on the projector, screen flicker may occur. This is not a fault. Wait 3 to 5 minutes until the lamp
lighting is stabilized.
When the Lamp mode is set to Eco, the Lamp indicator will light green.
If one of the following things happens, the projector will not turn on.
•
If the internal temperature of the projector is too high, the projector detects abnormal high temperature. In this
condition the projector will not turn on to protect the internal system. If this happens, wait for the projector's internal
components to cool down.
•
When the lamp reaches its end of usable life, the projector will not turn on. If this happens, replace the lamp. See
page
119
.
•
If the lamp fails to light, and if the STATUS indicator flashes on and off in a cycle of six times, wait a full minute and
then turn on the power.
POINTER
LASER
MAGNIFY
PAGE
OFF
POWER
ON
UP
DOWN
R
-
C
L
I
C
K
E
N
T
E
R
M
E
N
U
E
X
I
T
PC CARD
SOURCE
AUTO ADJUST
3D REFORM
LAMP
STATUS
POWER
ON/STAND BY
E
N
T
E
R
E
X
I
T
M
E
N
U
SELECT
POINTER
LASER
MAGNIFY
PAGE
OFF
POWER
ON
R
-
C
L
I
C
K
UP
DOWN
E
N
T
E
R
M
E
N
U
E
X
I
T
3.
To close the menu, press the EXIT button.
NOTE: Immediately after turning on the projector and
displaying an image, you cannot turn off the projector for 60
seconds.
After this has been done, you can proceed to the menu op-
eration.
If you want, you can select the menu language later. See "Lan-
guage" on page
91
.