Netgear FS728TP FS728TP Hardware manual - Page 12

Switch Features, Two Small Form-factor Pluggable SFP GBIC slots, which function as combo ports. Combo - power over ethernet switch

Get Netgear FS728TP - ProSafe 24 Port 10/100 Smart Switch PDF manuals and user guides
UPC - 606449050226
View all Netgear FS728TP manuals
Add to My Manuals
Save this manual to your list of manuals

Page 12 highlights

FS728TP Hardware Installation Guide Switch Features The following list identifies the key features of the NETGEAR Smart Switch. • 24 RJ-45 10/100 Fast Ethernet switching ports. • 4/ RJ-45 10/100/1000M auto sensing Gigabit Ethernet switching ports, two of which are Combo ports. • Two Small Form-factor Pluggable (SFP) GBIC slots, which function as combo ports. Combo ports are single ports with two physical connections, SFP fiber and RJ-45 copper. The RJ-45 copper ports corresponding to the Combo ports are the four 10/100/1000M auto-sensing Giga switching ports on each device. If both devices are plugged in, the fiber connection is active, with fiber port taking priority if both are connected. The following SFP types are supported: - 1000Base-SX - 1000Base-LX • The devices support full Netgear Smart Switch functionality. • The devices provide full compatibility with IEEE standards: - IEEE 802.3i, (10Base-T) - IEEE 802.3u (100Base-TX, 100Base-FX) - IEEE 802.3x (Full-duplex flow control) - IEEE 802.3ab (1000Base-T) - IEEE 802.3z (1000Base-X) - IEEE 802.3af (DTE Power via MDI) • Auto-sensing and auto-negotiating capabilities for all ports. • Auto Uplink™ on all ports to make the right connection. • Automatic address-learning function to build the packet-forwarding information table. The table contains up to 4K Media Access Control (MAC) addresses. • Full- and half-duplex functions for all 10/100/1000 Mbps ports. • Store-and-Forward transmission to remove bad packets from the network. • Full-duplex IEEE 802.3x pause frame flow control. 1-15 v1.0, November 2007 Introduction

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
FS728TP Hardware Installation Guide
1-15
Introduction
v1.0, November 2007
Switch Features
The following list identifies the key features of the NETGEAR Smart Switch.
•
24 RJ-45 10/100 Fast Ethernet switching ports.
•
4/ RJ-45 10/100/1000M auto sensing Gigabit Ethernet switching ports, two of which are
Combo ports.
•
Two Small Form-factor Pluggable (SFP) GBIC slots, which function as combo ports. Combo
ports are single ports with two physical connections, SFP fiber and RJ-45 copper. The RJ-45
copper ports corresponding to the Combo ports are the four 10/100/1000M auto-sensing Giga
switching ports on each device. If both devices are plugged in, the fiber connection is active,
with fiber port taking priority if both are connected.
The following SFP types are supported:
–
1000Base-SX
–
1000Base-LX
•
The devices support full Netgear Smart Switch functionality.
•
The devices provide full compatibility with IEEE standards:
–
IEEE 802.3i, (10Base-T)
–
IEEE 802.3u (100Base-TX, 100Base-FX)
–
IEEE 802.3x (Full-duplex flow control)
–
IEEE 802.3ab (1000Base-T)
–
IEEE 802.3z (1000Base-X)
–
IEEE 802.3af (DTE Power via MDI)
•
Auto-sensing and auto-negotiating capabilities for all ports.
•
Auto Uplink™ on all ports to make the right connection.
•
Automatic address-learning function to build the packet-forwarding information table. The
table contains up to 4K Media Access Control (MAC) addresses.
•
Full- and half-duplex functions for all 10/100/1000 Mbps ports.
•
Store-and-Forward transmission to remove bad packets from the network.
•
Full-duplex IEEE 802.3x pause frame flow control.