Netgear RNDP6310 ReadyNAS Pro User Manual - Page 24

Ethernet Interfaces, Standard Setting. - ip address

Get Netgear RNDP6310 - ReadyNAS Pro NAS Server PDF manuals and user guides
UPC - 606449059038
View all Netgear RNDP6310 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 24 highlights

ReadyNAS Pro Business Edition User Guide Ethernet Interfaces Select Network > Interfaces > Ethernet 1 /Ethernet 2 tab pages to specify network interfacespecific settings for Standard Settings, Teaming/Failover, VLAN Settings and Performance Settings. Standard Setting. In this section, you can specify the IP address, network mask, speed/duplex mode, and MTU settings. In most networks where a DHCP server is enabled, you can simply specify the Use values from a DHCP server option to automatically set the IP address and network mask. Figure 2-2 • IP Assignment. Select either Use values from a DHCP server or Use values below. - If you elect to assign the IP address using Use values from a DHCP server, NETGEAR advises that you set the lease time on the DHCP server/router to a value of at least a day. Otherwise, you might notice that the IP address of the unit changes even when it has been powered down for only a few minutes. Most DHCP servers allow you to assign a static IP address for specified MAC addresses. If you have this option, this would be a good way to ensure your ReadyNAS Pro Business Edition maintains the same IP address even in DHCP mode. - If you assign a static IP address by selecting Use values below, be aware that the browser will lose connection to the ReadyNAS Pro Business Edition device after the IP address has been changed. To reconnect after assigning a static IP address, open RAIDar and click Rescan to locate the device, and then reconnect. • Speed/Duplex Mode (Only applies to 10/100 connections). If you have a managed switch that works best if the devices are forced to a particular speed or duplex mode, you can select 2-2 Setting Up and Managing Your ReadyNAS Pro v1.2, October 2008

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
ReadyNAS Pro Business Edition User Guide
2-2
Setting Up and Managing Your ReadyNAS Pro
v1.2, October 2008
Ethernet Interfaces
Select Network > Interfaces > Ethernet 1 /Ethernet 2 tab pages to specify network interface-
specific settings for Standard Settings, Teaming/Failover, VLAN Settings and Performance
Settings.
Standard Setting.
In this section, you can specify the IP address, network mask, speed/duplex
mode, and MTU settings. In most networks where a DHCP server is enabled, you can simply
specify the
Use values from a DHCP server
option to automatically set the IP address and
network mask.
•
IP Assignment.
Select either
Use values from a DHCP server
or
Use values below.
–
If you elect to assign the IP address using
Use values from a DHCP server
, NETGEAR
advises that you set the lease time on the DHCP server/router to a value of at least a day.
Otherwise, you might notice that the IP address of the unit changes even when it has been
powered down for only a few minutes. Most DHCP servers allow you to assign a static IP
address for specified MAC addresses. If you have this option, this would be a good way to
ensure your ReadyNAS Pro Business Edition maintains the same IP address even in
DHCP mode.
–
If you assign a static IP address by selecting
Use values below
, be aware that the browser
will lose connection to the ReadyNAS Pro Business Edition device after the IP address has
been changed. To reconnect after assigning a static IP address, open RAIDar and click
Rescan
to locate the device, and then reconnect.
•
Speed/Duplex Mode (Only applies to 10/100 connections)
. If you have a managed switch
that works best if the devices are forced to a particular speed or duplex mode, you can select
Figure 2-2