Netgear WN604-100NAS User Manual - Page 56

Troubleshooting with the LEDs, All LEDs Are Off, WiFi LED Is Off

Get Netgear WN604-100NAS PDF manuals and user guides View all Netgear WN604-100NAS manuals
Add to My Manuals
Save this manual to your list of manuals

Page 56 highlights

Wireless N150 Access Point WN604 Troubleshooting with the LEDs You can use the LEDs on the front panel of the access point for troubleshooting. All LEDs Are Off It takes a few seconds for the Power LED to light up. Wait a minute and check the Power LED again. If the access point has no power. • Make sure the power adapter is connected to the access point.. • Make sure the power adapter is connected to a functioning power outlet. If it is in a power strip, make sure the power strip is turned on. If it is plugged directly into the wall, verify that it is not a switched outlet. • Make sure you are using the correct NETGEAR power adapter supplied with your access point. WiFi LED Is Off The wireless radio is turned off or the antenna is not working. There are two ways to turn off the wireless radio--the Wireless On/Off button on the side of the access point, and the Schedule Wireless Radio feature. Wireless On/Off Figure 7. You can use the Wireless On/Off button to control the wireless radio For information about the Schedule Wireless Radio feature, see Schedule the Wireless Radio on page 46. Check the following: 1. Make sure that the wireless radio is turned on. If it is, and the WiFi LED stays off, disconnect the access point from its power source and then plug it in again. 2. Make sure the antenna is securely connected to the access point. 3. Contact NETGEAR technical support if the WiFi LED remains off. Troubleshooting 56

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
Troubleshooting
56
Wireless N150 Access Point WN604
Troubleshooting with the LEDs
You can use the LEDs on the front panel of the access point for troubleshooting.
All LEDs Are Off
It takes a few seconds for the Power LED to light up. Wait a minute and check the Power LED
again.
If the access point has no power.
•
Make sure the power adapter is connected to the access point..
•
Make sure the power adapter is connected to a functioning power outlet. If it is in a power
strip, make sure the power strip is turned on. If it is plugged directly into the wall, verify
that it is not a switched outlet.
•
Make sure you are using the correct NETGEAR power adapter supplied with your access
point.
WiFi LED Is Off
The wireless radio is turned off or the antenna is not working. There are two ways to turn off
the wireless radio--the Wireless On/Off button on the side of the access point, and the
Schedule Wireless Radio feature.
Wireless On/Off
Figure 7. You can use the Wireless On/Off button to control the wireless radio
For information about the Schedule Wireless Radio feature, see
Schedule the Wireless Radio
on page 46.
Check the following:
1.
Make sure that the wireless radio is turned on. If it is, and the WiFi LED stays off,
disconnect the access point from its power source and then plug it in again.
2.
Make sure the antenna is securely connected to the access point.
3.
Contact NETGEAR technical support if the WiFi LED remains off.