NordicTrack 1750 Treadmill English Manual - Page 15

rate heart rate reading, continue to hold

Page 15 highlights

To reset the console, press the iFit Menu button in the upper right corner of the screen. To pause the workout, press the Pause button. To continue the workout, press the Resume button or the Start button. To end the workout and select a new workout, press the New Workout button. To end the workout, press the End Workout button. To measure your heart rate, stand on the walking platform and hold the metal contacts on the handrails for approximately ten seconds-avoid moving your hands. When your pulse is detected, your heart rate will be shown. For the most accurate heart rate reading, continue to hold the contacts for about 15 seconds. Note: The small wireless symbol in the upper right corner of the screen will show your wireless connection status. If the symbol is yellow, your treadmill is connected to your wireless network. If the symbol is green, your treadmill is connected to your wireless network and you have logged in to www.iFit.com. If the symbol does not appear, your treadmill is not connected to your wireless network. 6. Measure your heart rate if desired. 7. When you are finished exercising, remove the key from the console. Step onto the foot rails and press the Stop button repeatedly until a workout summary appears on the screen. After you view the workout summary, press the Done button. Then, remove the key from the console and put it in a secure place. When you are finished using the treadmill, press the power switch into the off position and unplug the power cord. IMPORTANT: If you do not do this, the treadmillʼs electrical components may wear prematurely. Before using the handgrip pulse sensor, remove the sheets of plastic from the metal contacts, if necessary. In addition, make sure that your hands are clean. Contacts 15

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36

15
To reset the console, press the iFit Menu button in
the upper right corner of the screen. To pause the
workout, press the Pause button. To continue the
workout, press the Resume button or the Start but-
ton. To end the workout and select a new workout,
press the New Workout button. To end the work-
out, press the End Workout button.
Note: The small wire-
less symbol in the
upper right corner of the
screen will show your
wireless connection sta-
tus. If the symbol is yel-
low, your treadmill is
connected to your wireless network. If the symbol
is green, your treadmill is connected to your wire-
less network and you have logged in to
www.iFit.com. If the symbol does not appear, your
treadmill is not connected to your wireless network.
6.
Measure your heart rate if desired.
Before using
the handgrip
pulse sensor,
remove the
sheets of plas-
tic from the
metal con-
tacts, if neces-
sary. In addi-
tion, make
sure that your
hands are clean.
To measure your heart rate,
stand on the walking
platform
and hold the metal contacts on the
handrails for approximately ten seconds—
avoid
moving your hands.
When your pulse is detected,
your heart rate will be shown.
For the most accu-
rate heart rate reading, continue to hold the
contacts for about 15 seconds.
7.
When you are finished exercising, remove the
key from the console.
Step onto the foot rails and press the Stop button
repeatedly until a workout summary appears on
the screen. After you view the workout summary,
press the Done button. Then, remove the key from
the console and put it in a secure place.
When you are finished using the treadmill, press
the power switch into the off position and unplug
the power cord.
IMPORTANT: If you do not do
this, the treadmillʼs electrical components may
wear prematurely.
Contacts