NordicTrack Vertex 670 English Manual - Page 14

Wrap the High Cable 73 around a 4 Pulley 35

Get NordicTrack Vertex 670 PDF manuals and user guides View all NordicTrack Vertex 670 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 14 highlights

26. Wrap the High Cable (73) around a 4" Pulley (35). 26 Attach the Pulley inside the slot in the Main Upright (3) with a 3/8" x 2 1/2" Bolt (54), two 3/8" Washers (55), two 5/8" x 1/2" Bushings (42), and a 3/8" Nylon Jamnut (63). 3 35 73 63 42 55 54 42 55 27. Disassemble the pre-assembled Pulley Plates (31). 27 Wrap the High Cable (73) around a 4" Pulley (35) in the direction shown. Attach the Pulley and a Cable Trap (44) to the top set of holes in the end of the Pulley Plates (31) with a 3/8" x 1 3/4" Bolt (60) and a 3/8" Nylon Jamnut (63). Make sure the Cable is in the groove of the Pulley and that the Cable Trap is oriented to hold the 63 Cable in place. 73 60 44 35 31 28. Route the High Cable (73) up through the indicated slot in the Top Frame (1), over a 4" Pulley (35), and back down through the Top Frame. Attach the 4" Pulley (35) inside the slot in the Top Frame (1) with a 3/8" x 2 1/2" Bolt (54), two 3/8" Washers (55), two 5/8" x 1/2" Bushings (42), and a 3/8" Nylon Jamnut (63). 28 55 63 1 42 73 35 Slot 55 42 54 14

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
14
26. Wrap the High Cable (73) around a 4” Pulley (35).
Attach the Pulley inside the slot in the Main
Upright (3) with a 3/8” x 2 1/2” Bolt (54), two 3/8”
Washers (55), two 5/8” x 1/2” Bushings (42), and
a 3/8” Nylon Jamnut (63).
26
55
42
63
3
35
42
55
54
73
27. Disassemble the pre-assembled Pulley Plates (31).
Wrap the High Cable (73) around a 4” Pulley (35)
in the direction shown. Attach the Pulley and a
Cable Trap (44) to the top set of holes in the end
of the Pulley Plates (31) with a 3/8” x 1 3/4” Bolt
(60) and a 3/8” Nylon Jamnut (63).
Make sure
the Cable is in the groove of the Pulley and
that the Cable Trap is oriented to hold the
Cable in place.
27
73
60
44
35
31
63
28. Route the High Cable (73) up through the indicat-
ed slot in the Top Frame (1), over a 4” Pulley
(35), and back down through the Top Frame.
Attach the 4” Pulley (35) inside the slot in the Top
Frame (1) with a 3/8” x 2 1/2” Bolt (54), two 3/8”
Washers (55), two 5/8” x 1/2” Bushings (42), and
a 3/8” Nylon Jamnut (63).
28
1
35
42
55
54
63
42
73
55
Slot