NordicTrack Xlt1200 Uk Manual - Page 10

Attach the Water Bottle Holder 26 to the Upright

Get NordicTrack Xlt1200 PDF manuals and user guides View all NordicTrack Xlt1200 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 10 highlights

9. Apply a film of grease to the barrel of an M8 x 55mm Bolt Set (92) and to a 7mm Spacer (55). Slide an 9 M8 Washer (69) and the Spacer onto the barrel. While another person holds the front end of the Left Pedal Leg (14) inside the bracket on the left Handlebar Leg (17), insert the barrel of the Bolt Set (92) through both parts. Next, slide a 7mm Spacer (55) and an M8 Washer (69) onto the end of the barrel of the Bolt Set. Then, turn the screw of the Bolt Set a few turns into the barrel. Do not overtighten the Bolt Set; the left Handlebar Leg must pivot freely. Attach the right Handlebar Leg (not shown) to the Right Pedal Leg (not shown) in the same way. See step 7. Tighten the four M8 x 38mm Button Screws (58). 17 Grease 55 55 92 69 92 69 14 10.While another person holds the Display Console (74) and the Control Console (75) near the Upright (2), connect the Pulse Jumper Wire (76) to the console pulse wire. Then, connect the Upper Wire Harness (77) to the console wire harness. Insert the excess wires into the Upright. Set the Consoles (74, 75) on the Upright (2). Attach the Consoles with six M4 x 16mm Screws (47). Avoid pinching the wires. Do not tighten the Screws yet. 10 47 Console Pulse 2 Wire 76 47 77 74 75 Console Wire Harness 11.Attach the Water Bottle Holder (26) to the Upright 11 (2) with two M4 x 19mm Screws (57). 57 2 See step 10. Tighten the six M4 x 16mm Screws (47). 26 12. Make sure that all parts of the elliptical exerciser are properly tightened. Cover the floor beneath the elliptical exerciser to protect the floor from damage. Note: Some extra hardware may be left over. 10

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
10
9.
Apply a film of grease to the barrel of an M8 x 55mm
Bolt Set (92) and to a 7mm Spacer (55). Slide an
M8 Washer (69) and the Spacer onto the barrel.
While another person holds the front end of the
Left Pedal Leg (14) inside the bracket on the left
Handlebar Leg (17), insert the barrel of the Bolt
Set (92) through both parts. Next, slide a 7mm
Spacer (55) and an M8 Washer (69) onto the end
of the barrel of the Bolt Set. Then, turn the screw
of the Bolt Set a few turns into the barrel.
Do not
overtighten the Bolt Set; the left Handlebar Leg
must pivot freely.
Attach the right Handlebar Leg (not shown) to
the Right Pedal Leg (not shown) in the same
way.
See step 7.
Tighten the four M8 x 38mm Button
Screws (58).
10.While another person holds the Display Console
(74) and the Control Console (75) near the Upright
(2), connect the Pulse Jumper Wire (76) to the con-
sole pulse wire. Then, connect the Upper Wire
Harness (77) to the console wire harness. Insert
the excess wires into the Upright.
Set the Consoles (74, 75) on the Upright (2). Attach
the Consoles with six M4 x 16mm Screws (47).
Avoid pinching the wires. Do not tighten the
Screws yet.
14
9
10
2
92
17
92
55
55
69
69
47
47
77
76
Console
Pulse
Wire
Console
Wire
Harness
75
74
11.Attach the Water Bottle Holder (26) to the Upright
(2) with two M4 x 19mm Screws (57).
See step 10
. Tighten the six M4 x 16mm Screws
(47).
11
2
Grease
26
57
12.
Make sure that all parts of the elliptical exerciser are properly tightened.
Cover the floor beneath the el-
liptical exerciser to protect the floor from damage. Note: Some extra hardware may be left over.