Oki MICROLINE 186 Plus - Serial Users Guide - Page 68

Problem 8, Solution, torn, causing alignment problems.

Get Oki MICROLINE 186 Plus - Serial PDF manuals and user guides View all Oki MICROLINE 186 Plus - Serial manuals
Add to My Manuals
Save this manual to your list of manuals

Page 68 highlights

Problem 8 The ALARM light is flashing. Solution Try turning the printer off, then back on again. If the light still blinks, call for service. Problem 9 The Print Quality and Character Pitch keys on the front panel don't work. Solution The Operator Panel Function in the printer menu can be used to disable these buttons (Limited Function). If the printer is part of a customized system or if it is used by a number of people, the system manager may have used this option to make sure the printer is always set properly. Check with your system manager before changing any menu settings. Problem 10 My printer keeps indicating "Paper out" even though there is paper installed. Solution The most likely cause is that the paper sensor groove at the left end of the platen is not covered by the paper. Move the paper over to cover the sensor groove. Problem 11 When I am using continuous feed paper, the sprocket holes are torn, causing alignment problems. Solution The most likely cause is that the paper lever (right side of printer) is in the single sheet position. Make sure the lever is in the continuous forms position (forward). 68 • Troubleshooting

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
68
• Troubleshooting
Problem 8
__________________________________________
The ALARM light is flashing.
Solution
Try turning the printer off, then back on again. If the light still blinks, call for
service.
Problem 9
__________________________________________
The Print Quality and Character Pitch keys on the front panel don't
work.
Solution
The Operator Panel Function in the printer menu can be used to disable these
buttons (Limited Function). If the printer is part of a customized system or if it
is used by a number of people, the system manager may have used this
option to make sure the printer is always set properly.
Check with your system manager before changing any menu settings.
Problem 10
_________________________________________
My printer keeps indicating "Paper out" even though there is paper
installed.
Solution
The most likely cause is that the paper sensor groove at the left end of the
platen is not covered by the paper. Move the paper over to cover the sensor
groove.
Problem 11
_________________________________________
When I am using continuous feed paper, the sprocket holes are
torn, causing alignment problems.
Solution
The most likely cause is that the paper lever (right side of printer) is in the
single sheet position. Make sure the lever is in the continuous forms position
(forward).