Home » Oki Manuals » Dot Matrix Printers » Oki MICROLINE 8810 » Manual Viewer

Oki MICROLINE 8810 Users Guide - Page 34

Setup, bold blue, Bi-directional, Not Tear Off, Valid, Bottom Detect, Manual, CSF Rear, 1 CPI

Add to My Manuals
Save this manual to your list of manuals

Page 34 highlights

Setup Note The default setting is in bold blue type. Item Multi Pass Graphics Graphics Data (ML Only) Rcv. Buffer Data Word (ML Only) Panel Function Path Change CutSheet Smooth Skp Ovr Binding High Skip Eject Condition Sheet Feed Mode (Applies only if the optional CSF is installed.) CSF Select (Applies only if the optional CSF is installed.) Print Suppress Auto LF Auto CR Print DEL Code SI Pitch (10) SI Pitch (12) Reset Inhibit ESC SI Pitch (IBM Only) Settings Bi-directional, Uni-directional Bi-directional, Uni-directional 8 Bits, 7 Bits 128, 0 K 8 Bits, 7 Bits Full, Limited Not Tear Off, Tear Off Valid, Invalid Invalid, Valid 1, Valid 2 Yes, No Bottom Detect, FF Code Manual, CSF CSF Front, CSF Rear No, Yes No, Yes No, Yes No, Yes 15 CPI, 17.1 CPI 12 CPI, 20 CPI No, Yes 17.1 CPI, 20 CPI Microline 8810 User's Guide Menu Summary • 34

Section	Page
Copyright Information	2
Document Information	2
Disclaimer	2
Trademark Information	2
Contents	3
Introduction	6
Features	6
Front View, Outside	7
Front View, Inside (1)	8
Front View, Inside (2)	8
Rear View	9
Control Panel	10
Individual Switches	10
Combined Switches	12
With the Printer Powered Up and Off Line	12
Control Panel Lights	14
Quick Reference: Control Panel Functions	16
Print Modes	17
Change Print Mode	17
Change to Quiet	17
Change to Normal	17
Loading Print Media	18
Individual Sheets/Forms (“MANUAL”)	18
Specifications	19
Load Individual Sheets/Forms	20
Continuous Forms (“FRONT”)	21
Specifications	21
Load Continuous Forms	21
Switch between Single Sheets and Continuous Forms	25
Single Sheets to Continuous Forms	25
Manual Feed to Front Feed	25
Continuous Forms to Single Sheets	25
Front Feed to Manual Feed	25
The Printer Menu	26
Print the Menu	26
Navigating the Menu	27
Groups, Items, and Settings	27
Access the Menu	27
Scrolling Through Groups, Items and Settings	27
Exit the Menu	28
Example: Turn on Proportional Spacing and Form Tear-Off	28
Reset to Factory Defaults	28
Print the Menu	29
Single Sheet (Manual Feed)	29
Continuous Forms (Front Feed)	31
Menu Summary	32
CSF Front	38
CSF Rear	39
Front Feed	40
Adjustment	43
Explanation of Menu Items	46
1stDotAdjAlign	46
1stDotAdj: Single Sheets/Forms	46
1stDotAdj: Continuous Forms	47
Align1 Pos. Adj.	47
Align2 Pos. Adj.	47
Align3 Pos. Adj	47
Align4 Pos. Adj.	47
Auto Align	48
Auto Align Detect	48
Auto Align (POW)	49
Auto CR	49
Auto Eject Pos.	49
Auto Feed XT	49
Auto Gap Timing	49
Auto LF	49
Auto Select	50
Baud Rate	50
Bi-Direction	50
Busy Line	50
Busy Time	50
Buzzer	50
Buzzer Volume	50
Character Set	50
Check Print Area	51
Code Page	51
Cont. I-Prime	51
CSF Select	51
CutSheet Smooth	51
Data Word	51
Diagnostic Test	51
DRAFT Mode	51
DSR Signal	52
DTR Signal	52
Eject Direction	52
Eject Dir.	52
Emulation Mode	52
ESC SI Pitch	52
FF Function	52
Form Tear-Off	52
Front Load Adj.	53
Gap Control	54
Gap Pos.	55
Graphics	55
Graphics Data	55
High Skip	55
Host Interface	55
I-Prime	55
I/F Time Out	55
Impact Mode	55
Initial Pos.	56
Language Set	56
Line Spacing	56
LF Revise	56
Load LF Speed	56
Manual Feed CSF	56
Manual Sheet CSF	57
Memory Auto Align	57
Multi Pass	57
Page Length	57
Page Width	57
Panel Function	57
Paper End	57
Parallel I/F	58
Parity	58
Path Change	58
PE Adj. [Paper End Adjust]	59
PE Pos. [Paper End Position]	59
Pitch	59
Power Save Time	60
Power Saving	60
Print DEL Code	60
Print Dir. Cmd.	60
Print Mode	60
Print Suppress	60
Prop. Spacing	60
Protocol	60
Rcv. Buffer	60
Rear Load Adj.	61
Regist. Low	61
Regist. Normal	61
Regist. High 1	61
Regist. High 2	61
Remove Sheet Wait	61
Reset Inhibit	61
Serial Data	61
Set Alarm	62
Sheet Feed Mode	62
SI Pitch (10)	62
SI Pitch (12)	62
Size	62
Skew Detect	63
Skp Ovr Binding	63
Skip Over Perf.	63
Style	63
Tear Mode	64
Time Out Print	64
TOF	64
TOF Adj. (Cut)	64
TOF Adj. (CSSF)	65
TOF Adj. (CSFR)	65
Wait Time	65
Zero Character	65
Auto Align	66
Disabling Auto Align	66
Set Top of Form (TOF)	67
General Information	67
Use the Printer Menu	67
Use 1Chr Set Pos	68
Front Feed (Continuous Forms)	68
Manual Feed (Single Sheets/Forms)	69
Temporary TOF	71
Use the Control Panel	71
Form Tear Off	72
Turn On Forms Tear Off	72
Move Continuous Forms Up for Tear Off	72
Tests	73
Rolling ASCII Test	73
Font Sample Test	73
Hex Dump Mode	74
Engaging the Hex Dump Mode	74
Running a Hex Dump Test	74
Exiting Hex Dump Mode	74
Setting the Printhead Gap	75
General Information	75
Printhead Gap Settings	76
Change to a Manual Printhead Gap Setting	77
“On-the-Fly”	77
In the Menu	77
Troubleshooting	79
Paper Jams, Individual Sheets/Forms	79
Paper Jams, Continuous Forms	81
Paper Jams, Repetitive	82
Error Messages	85
Maintenance	88
Replace the Ribbon	88
Clean the Housing	93
Specifications	94
Print Method	94
Printhead	94
Emulations	94
Interfaces (Standard)	94
Receive Buffer Size	94
Print Speed	94
Characters per Line (CPL)	94
Graphics Resolution	95
Resident Fonts	95
Reliability	95
Print Media Specifications	95
Printer Dimensions	98
Printer Weight	98
Environmental Requirements	98
Electrical Requirements	98
Utilities	99
Overview	99
Accessing	99
Descriptions of Utilities	100
Direct Network Printing Utility (LPR)	100
OKI DIPUS (Dot Impact Printer Utilities)	100
Network Setup Utility	100
PrintSuperVision	100
Installing the Utilities	101
Windows	101
Direct Network Printing Utility (LPR)	102
General Information	102
How to Install	102
Direct Network Printing Utility (LPR) Status Box	103
Additional Information	103
OKI DIPUS (Dot Impact Printer Utilities)	104
General Information	104
How to Install	104
Additional Information	104
Status Monitor	104
Menu Setup Utility	104
Top of Form Setup Utility	104
Switch Setup Utility	104
Network Setup Utility	105
General Information	105
How to Install	105