Oki ML8810 ML8810 User's Guide - English - Page 72

Manual Feed (Single Sheets/Forms), Simultaneously press SHIFT and SEL.

Get Oki ML8810 PDF manuals and user guides View all Oki ML8810 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 72 highlights

c. To move the TOF further up on the page (print paper retracts further out of the printer): - In 1/144-inch (0.18 mm) increments: press and hold the SHIFT switch, then press LF. - In 10/144-inch (1.75 mm) increments: press and hold the SHIFT switch, then press MODE. 5. Store the TOF position in the printer's memory: a. To store the position as the 1Chr. Set Pos setting, press the SEL switch. The setting will be retained, even if you turn the printer off, until you use this procedure to change the setting. This also automatically sets the TOF setting in the Front Feed group to 1Chr. Set Pos. Note If you reset the printer to the factory defaults, the 1Chr. Set Pos you have established will be deleted. b. To store the position in the printer's memory only until it is turned off or it receives an I-Prime signal, press the LOAD switch. 6. Press SEL to return the printer to the on-line state. Use 1Chr Set Pos Manual Feed (Single Sheets/Forms) 8810_3_crop.jpg 1. Make sure the printer is set to the Manual Feed path. 2. Press SEL, then press LOAD to remove the paper from the manual feed path. 3. Simultaneously press SHIFT and SEL. The SEL light starts blinking and the display reads 1CHR. SET MODE INSERT PAPER. 4. Load a sheet/form on the platform. The sheet/form advances to the printer's default TOF (1/4-inch [6.4 mm]) and the display reads 1CHR. SET POS. Microline 8810 User's Guide 72

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
Microline 8810 User°s Guide
72
c.
To move the
TOF
further
up
on the page (print paper retracts
further out of the printer):
´
In 1/144-inch (0.18 mm) increments: press and hold the SHIFT
switch, then press LF.
´
In 10/144-inch (1.75 mm) increments: press and hold the SHIFT
switch, then press MODE.
5.
Store the TOF position in the printer°s memory:
a.
To store the position as the 1Chr. Set Pos setting, press the SEL
switch. The setting will be retained, even if you turn the printer off,
until you use this procedure to change the setting. This also
automatically sets the TOF setting in the Front Feed group to 1Chr.
Set Pos.
Note
If you reset the printer to the factory defaults, the 1Chr. Set
Pos you have established will be deleted.
b.
To store the position in the printer°s memory only until it is turned
off or it receives an I-Prime signal, press the LOAD switch.
6.
Press SEL to return the printer to the on-line state.
Use 1Chr Set Pos
Manual Feed (Single Sheets/Forms)
1.
Make sure the printer is set to the Manual Feed path.
2.
Press SEL, then press LOAD to remove the paper from the manual feed
path.
3.
Simultaneously press SHIFT and SEL.
The SEL light starts blinking and the display reads
1CHR. SET MODE
INSERT PAPER.
4.
Load a sheet/form on the platform.
The sheet/form advances to the printer²s default TOF (1/4-inch [6.4
mm]) and the display reads 1CHR. SET POS.
8810_3_crop.jpg