Onkyo HT-RC370 Owner Manual

Onkyo HT-RC370 Manual

Get Onkyo HT-RC370 PDF manuals and user guides View all Onkyo HT-RC370 manuals
Add to My Manuals
Save this manual to your list of manuals

Onkyo HT-RC370 manual content summary:

  • Onkyo HT-RC370 | Owner Manual - Page 1
    AV Receiver HT-RC370 Instruction Manual Thank you for purchasing an Onkyo AV Receiver. Please read this manual thoroughly before making connections and plugging in the unit. Following the instructions in this manual will enable you to obtain optimum performance and listening enjoyment from your new
  • Onkyo HT-RC370 | Owner Manual - Page 2
    user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. Important Safety Instructions 1. Read these instructions. 2. Keep these instructions rear. The rear edge of the shelf or board above the apparatus shall be set 10 cm
  • Onkyo HT-RC370 | Owner Manual - Page 3
    sound checked by your Onkyo dealer. 8. instructions user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver LA NORME NMB003 DU CANADA. Sur les modèles
  • Onkyo HT-RC370 | Owner Manual - Page 4
    Speaker setup microphone (➔ page 31) Remote controller (RC-807M) and two batteries (AA/R6) (Note for China: The battery for the remote controller remote controller To use the remote controller, point it at the AV receiver's remote control sensor, as shown below. Remote control sensor AV receiver
  • Onkyo HT-RC370 | Owner Manual - Page 5
    Commands 70 Using Normal Macros 71 Appendix Troubleshooting 72 Firmware Update 78 Connection Tips and Video Signal Path 81 Using an RIHD-compatible TV, Player, or Recorder 84 About HDMI 86 Network/USB Features 87 Specifications 90 To reset the AV receiver to its factory defaults, turn it on
  • Onkyo HT-RC370 | Owner Manual - Page 6
    • THX Select2 Plus*1 Certified • Incorporates Qdeo™*2 technology for HDMI Video Upscaling (to 4K Compatible) • HDMI (Audio Return Channel, 3D Pandora/Rhapsody/Slacker/ Mediafly/Napster) * Services available may vary depending on the region. • Network Capability for Streaming Audio Files*11 •
  • Onkyo HT-RC370 | Owner Manual - Page 7
    . This HD Radio Ready™ receiver is ready to receive HD Radio broadcasts when connected to the Onkyo UP-HT1 HD Radio tuner module (sold separately). *11 "DLNA®, the DLNA Logo and DLNA CERTIFIED™ are trademarks, service marks, or certification marks of the Digital Living Network Alliance." *11 Windows
  • Onkyo HT-RC370 | Owner Manual - Page 8
    ON/STANDBY button (22) C ZONE 2, OFF buttons (63) D Remote control sensor (4) E Display (9) F LISTENING MODE buttons (34) G DIMMER AUX INPUT HDMI jack (17) R TONE and Tone Level buttons (60) S Input selector buttons (23) T VIDEO jack (18) U USB port (18) V SETUP MIC jack (31) W HDMI THRU indicator
  • Onkyo HT-RC370 | Owner Manual - Page 9
    Display BCDE F GH I JK L M N OP For detailed information, see the pages in parentheses. B Speaker/channel indicators H Audio input indicators C Z2 (Zone 2) indicator (63) I Bi AMP indicator (14, 46) D Listening mode and format indicators (34, 61) E ,  and cursor indicators (24) F NET
  • Onkyo HT-RC370 | Owner Manual - Page 10
    R B DIGITAL IN COAXIAL and OPTICAL jacks C V REMOTE CONTROL jack D UNIVERSAL PORT jack E ETHERNET port F MONITOR OUT V and S jacks G HDMI IN and OUT jacks H COMPONENT VIDEO IN and MONITOR 2 L/R) R AC INLET (Chinese models) See "Connecting the AV Receiver" for connection (➔ pages 12 to 21). En 10
  • Onkyo HT-RC370 | Owner Manual - Page 11
    Controller Controlling the AV Receiver B C D *1 E F B G H I C To control the AV receiver, press RECEIVER to select Receiver mode. J You can also use the remote controller to control D Onkyo Blu-ray Disc/DVD player, CD player, and other components. See "Entering Remote Control Codes" for
  • Onkyo HT-RC370 | Owner Manual - Page 12
    Connections Connecting the AV Receiver Connecting Your Speakers Connecting the Speaker Cables The following illustration shows which speaker should be connected to each pair of terminals. If you're using
  • Onkyo HT-RC370 | Owner Manual - Page 13
    best from your surround sound system, you need to set the speaker settings automatically (➔ page 31) or manually • Read the instructions supplied with your AV receiver. • Make sure the metal core of the wire does not have contact with the AV receiver's rear panel. Doing so may damage the AV receiver
  • Onkyo HT-RC370 | Owner Manual - Page 14
    Dipole speakers output the same sound in two directions. Dipole Using a Powered Subwoofer To find the best position for your subwoofer, while playing support biamping. Refer to your speaker manual. Bi-amping provides improved bass and treble performance. When bi-amping is used, the AV receiver
  • Onkyo HT-RC370 | Owner Manual - Page 15
    you want to use a more powerful power amplifier, you can use the AV receiver as a preamp. Connect all speaker outputs to the power amplifier. See the manuals supplied with your amplifier for details. Note *1 Specify "None" for any channel that you don't want to output (➔ page 46). SB···Surround Back
  • Onkyo HT-RC370 | Owner Manual - Page 16
    AV connections, read the manuals supplied with your AV components. • Don't connect the power cord until you've completed and double-checked all AV enjoy digital sound such as channel HDMI connection, 176.4/192 kHz is also available. Note • The AV receiver does not support SCART plugs. • The AV receiver
  • Onkyo HT-RC370 | Owner Manual - Page 17
    TV Out" setting is set to "On" (➔ page 58) to hear from your TV speakers, the sound will also be output from the AV receiver's speakers if you adjust the volume of the AV receiver. Similarly, as the "HDMI Control(RIHD)" setting is set to "On" (➔ page 57) to hear from the speakers of an Q-compatible
  • Onkyo HT-RC370 | Owner Manual - Page 18
    Connecting Your Components The on-screen menus appear only on a TV that is connected to the HDMI OUT. If your TV is connected to other video outputs, use the AV receiver's display when changing settings. "# $ %& ' () * En 18
  • Onkyo HT-RC370 | Owner Manual - Page 19
    IN. See your turntable's manual for details. If your turntable has a ground wire, connect it to the AV receiver's GND screw. With some the HDMI outputs. However, if you have assigned the HDMI inputs to the PC input selector, the AV receiver will output signals received from the HDMI inputs
  • Onkyo HT-RC370 | Owner Manual - Page 20
    AV receiver. The other jack is for connecting additional V-capable components. • Connect only Onkyo components to V jacks. Connecting other manufacturer's components may cause a malfunction. • Some components may not support all V functions. Refer to the manuals • The surround sound and DSP listening
  • Onkyo HT-RC370 | Owner Manual - Page 21
    equipment on the same circuit. If this is a problem, plug the AV receiver into a different branch circuit. • Do not use a power cord other than the one supplied with the AV receiver. The supplied power cord is designed exclusively for use with the AV receiver and should not be used with any other
  • Onkyo HT-RC370 | Owner Manual - Page 22
    Turning On & Basic Operations Turning On/Off the AV Receiver ON/STANDBY RECEIVER RECEIVER Turning On 1 Press ON/STANDBY on the front panel. or Press RECEIVER followed by RECEIVER on the remote controller. The AV receiver comes on, the display lights. Turning Off 1 Press ON/STANDBY on the front
  • Onkyo HT-RC370 | Owner Manual - Page 23
    HDMI OUT. If your TV is connected to other video outputs, use the AV receiver's display when changing settings. This section describes the procedure for using the remote controller unless otherwise specified. Controlling Contents of USB or Network menu for each media or service. C R/X and ENTER
  • Onkyo HT-RC370 | Owner Manual - Page 24
    service. on the front of the AV receiver. While reading the contents of your It will flash if the AV receiver cannot read the iPod/iPhone AV receiver stores the mode. This means that if you disconnect when in Extended Mode (Music), the AV receiver front of the AV receiver, while the message "Connecting..."
  • Onkyo HT-RC370 | Owner Manual - Page 25
    Radio You need to connect the AV receiver to your home network (➔ page 87). You can select Internet radio stations by connecting to the AV receiver from your computer and selecting stations in your web browser. Internet radio URLs in the following formats are supported: PLS, M3U, and podcast (RSS
  • Onkyo HT-RC370 | Owner Manual - Page 26
    Setup Menu). Note • The AV receiver's IP address is shown on "IP Address" (➔ page 59). • If you're using DHCP, your router may not always allocate the same IP address to the AV receiver, so if you find that you can't connect to the AV receiver, recheck the AV receiver's IP address on the "Network
  • Onkyo HT-RC370 | Owner Manual - Page 27
    media servers which do not support this function. • Photos and movies stored on a media server cannot be accessed from the AV receiver. • Depending on the sharing settings in the media server, the AV receiver may not able to access the content. See the instruction manual of the media server. 5 Use
  • Onkyo HT-RC370 | Owner Manual - Page 28
    Setup in your browser. The volume value of the remote window and the volume value of the AV receiver may not always match. Adjustments you make to the volume in the AV receiver will not be reflected in the "Remote manual tuning mode and listen to the station in mono. ■ Manual tuning mode In manual
  • Onkyo HT-RC370 | Owner Manual - Page 29
    to store the station or channel. The station or channel is stored and the preset AV receiver, or the remote controller's CH +/-. Tip • You can also use the remote controller's number buttons to select a preset directly. The AV receiver supports four types of RDS information: PS (Program Service
  • Onkyo HT-RC370 | Owner Manual - Page 30
    PRESET F/S to select the type of program you want. See the table shown later in this chapter. 3 To start the search, press ENTER. The AV receiver searches until it finds a station of the type you specified, at which point it stops briefly before continuing with the search. 4 When a station you want
  • Onkyo HT-RC370 | Owner Manual - Page 31
    and connect it to the SETUP MIC jack. SETUP MIC jack Speaker setup microphone The speaker setting menu appears. Note • The on-screen menus appear only on a TV that is connected to the HDMI OUT. If your TV is connected to other video outputs, use the AV receiver's display when changing settings. En
  • Onkyo HT-RC370 | Owner Manual - Page 32
    to select an option, and then press ENTER. MultEQ XT: Auto Setup AUDYSSEY -- Review Speaker Configuration -- Subwoofer : Front : Center : Surround : Front Wide Setup. • If the AV receiver is muted, it will be unmuted automatically when Audyssey MultEQ XT Room Correction and Speaker Setup
  • Onkyo HT-RC370 | Owner Manual - Page 33
    your Onkyo THX recommends setting them manually. Using a Powered Subwoofer If you're using a powered subwoofer and it outputs very low-frequency sound at a low volume level, it may not be detected by Audyssey MultEQ XT Room Correction and Speaker Setup. If the "Subwoofer" appears on the "Review
  • Onkyo HT-RC370 | Owner Manual - Page 34
    button selects the THX listening modes. PURE AUDIO button and indicator This button selects the Pure Audio listening mode. When this mode is selected, the AV receiver's display and video circuitry are turned off. Only video signals input through HDMI input can be output from HDMI OUT. The indicator
  • Onkyo HT-RC370 | Owner Manual - Page 35
    Dolby Digital EX surround sound. This provides a center back surround channel from 5.1-channel sources. Speaker Layout The illustration shows which speakers are activated in each channel. See "Speaker Configuration" for the speaker setup (➔ page 46). ; 9 $ # C 7 Press RECEIVER followed by SP
  • Onkyo HT-RC370 | Owner Manual - Page 36
    much of the processing set via Home menu is disabled. A/V Sync does not have effect on the analog audio. See "Advanced Setup" for more details (➔ page 43). Sound is output from the front left and right speakers and subwoofer. Speaker Layout ;9$ /*3 ;9$ / Use this mode when watching an old movie
  • Onkyo HT-RC370 | Owner Manual - Page 37
    Mode Description Input Source Dolby Pro Logic IIx*4 Dolby Pro Logic IIx expands any 2-channel source for 7.1-channel Dolby Pro Logic II playback. It provides a very natural and seamless surround-sound experience that fully envelops the listener. As well as music and movies, video games
  • Onkyo HT-RC370 | Owner Manual - Page 38
    He Xo : M6 u s i c THX Game s Description Input Source This mode expands any 2-channel source for up to 7.1-channel playback. It uses seven full-bandwidth channels of matrix decoding for matrix-encoded material, providing a very natural and seamless surround sound experience that fully envelops
  • Onkyo HT-RC370 | Owner Manual - Page 39
    THX Cinema • Neo:6 Music + THX Music 4 • Neo:6 + THX Cinema • Neo:6 + THX Music • Neo:6 + THX Games The combination of Neo:6 and THX Cinema channel speaker system. *6 AV receiver can input the DSD signal from HDMI IN. Setting the output setting on the player side to PCM might obtain a better sound
  • Onkyo HT-RC370 | Owner Manual - Page 40
    grouped in the following categories: MOVIE/TV, MUSIC, GAME and THX. Use R/X to select the category and F/S to select the channels shown here output the sound. Using the Sleep Timer With the sleep timer, you can set the AV receiver to turn off automatically after a specified period. 1 Press RECEIVER
  • Onkyo HT-RC370 | Owner Manual - Page 41
    RECEIVER Onkyo support front high, front wide or surround back speakers is used, this setting cannot be selected. Muting the AV Receiver You can temporarily mute the output of the AV receiver. 1 Press RECEIVER cancelled when the AV receiver is set to on this device, no sound will be output from the
  • Onkyo HT-RC370 | Owner Manual - Page 42
    Onkyo components via simple commands from a single-button press. These commands are user-definable remote controller. ■ MY TV First, the TV, the cable set-top box, and the AV receiver are turned on. Then the input selector is set to "CBL/SAT". ■ MY MUSIC The Onkyo CD player and the AV receiver
  • Onkyo HT-RC370 | Owner Manual - Page 43
    THX Audio Setup D Audio Adjust (➔ page 49) 7. Hardware Setup 1. Remote ID 2. Tuner 3. HDMI 4. Auto Standby 5. Network 6. Firmware Update I Remote Controller Setup on the AV receiver by using SETUP, the arrow buttons, and ENTER. • During Audyssey MultEQ® XT Room Correction and Speaker Setup, messages
  • Onkyo HT-RC370 | Owner Manual - Page 44
    that of 1080p, resulting in 3840 × 2160 pixels. You can specify the output resolution for the HDMI OUT and have the AV receiver upconvert the picture resolution as necessary to match the resolution supported by your TV. Note • Depending on the incoming video signal, the video playback may not be
  • Onkyo HT-RC370 | Owner Manual - Page 45
    component has been connected Output composite video and S-Video sources from the HDMI output. Note • If you connect a component (such as UP- the LFE channel from their analog subwoofer output at 15 dB higher than normal. With this setting, you can change the AV receiver's subwoofer sensitivity
  • Onkyo HT-RC370 | Owner Manual - Page 46
    Sounds below the crossover frequency will be output by the subwoofer instead of the speaker. Refer to your speaker's manuals to determine the optimum crossover frequencies. If you set up your speakers using Audyssey MultEQ XT Room Correction and Speaker Setup, please make sure manually that any THX
  • Onkyo HT-RC370 | Owner Manual - Page 47
    THX-certified speakers, select "80Hz". ■ Double Bass This setting is NOT set automatically by Audyssey MultEQ® XT Room Correction and Speaker Setup function (➔ page 31). ` On ` Off(THX) Turn this setting on to boost bass output by feeding bass sounds from the front left, right, and center channels
  • Onkyo HT-RC370 | Owner Manual - Page 48
    - "HDMI Control(RIHD)" is set to "On" (➔ page 57) and you're listening through your TV speakers. - the AV receiver is bass sounds; high frequencies (e.g., 16000Hz) affect treble sounds. 3 Use R to select "Channel", over this setting (➔ page 51). THX Audio Setup ■ Surr Back Speaker Spacing `
  • Onkyo HT-RC370 | Owner Manual - Page 49
    technology featured in THX Ultra2 Plus™ and THX Select2 Plus™ Certified receivers. With THX Loudness Plus, home theater audiences can now experience the rich details in a surround mix at any volume level. A consequence of turning the volume below Reference Level is that certain sound elements can be
  • Onkyo HT-RC370 | Owner Manual - Page 50
    mix, allowing you to adjust the weight of the center channel sound. ■ PL IIz Height Gain ` Low ` Mid ` High EX flag, the Dolby EX or THX Surround EX listening mode is used. ` Manual: You can select any available listening or source components, freeing the user from having to make volume adjustments
  • Onkyo HT-RC370 | Owner Manual - Page 51
    channel output is attenuated in order to create the center channel. Changing the value from "0" to "5" will spread the sound of the center channel CD) sources Source Setup Items can be set sound even when listening at low volume levels. Audyssey Dynamic EQ solves the problem of deteriorating sound
  • Onkyo HT-RC370 | Owner Manual - Page 52
    or Audyssey Dynamic Volume® with THX listening modes, set the "Loudness Plus" setting to "Off" and set "Preserve THX Settings" to "No" (➔ Audyssey Dynamic EQ solves the problem of deteriorating sound quality as volume is television channels, or changing from stereo to surround sound content,
  • Onkyo HT-RC370 | Owner Manual - Page 53
    player, you may find that the picture and sound are out of sync. With this setting, you adjust will depend on whether your TV or display supports HDMI Lip Sync and if the "Lip Sync" setting by using +10 on the remote controller. *2 Press CLR on the remote controller to delete all the characters
  • Onkyo HT-RC370 | Owner Manual - Page 54
    44). ■ Picture Mode*1 ` Custom: All settings can be performed manually. ` Cinema: Select when the picture source is a movie or change resolution). When video is output from HDMI OUT, it is processed the same as the appropriate conversion is applied. The AV receiver will adjust to the picture source,
  • Onkyo HT-RC370 | Owner Manual - Page 55
    on the remote controller by using PCM: Only 2-channel PCM format input sound. When "HDMI", "COAXIAL" or "OPTICAL" is selected in the "Audio Selector" setting, you can then specify the signal type in "Fixed Mode". Normally, the AV receiver AV receiver, or - the docked iPod/iPhone model is not supported
  • Onkyo HT-RC370 | Owner Manual - Page 56
    AV receiver has specific to analog sound. • For the when 2-channel (2/0) stereo HDMI IN such as DVD-Audio, and DSD multichannel sources such as Super Audio CD. Miscellaneous Main menu Miscellaneous Volume Setup ■ Volume Display ` Absolute: Displayed range is Min, 0.5 to 99.5, Max. `Relative (THX
  • Onkyo HT-RC370 | Owner Manual - Page 57
    the setting to "Off". • Refer to the connected component's instruction manual for details. • When "HDMI Control(RIHD)" setting is set to "On", the power consumption on standby mode slightly increases. (Depending on the TV status, the AV receiver will enter standby mode as usual.) • When the source
  • Onkyo HT-RC370 | Owner Manual - Page 58
    (RIHD)", "HDMI Through" or "Audio Return Channel" turn off the power on all connected pieces of equipment and then turn them on again. Refer to the user's manuals for all connected pieces of equipment. Auto Standby ■ Auto Standby ` Off ` On When "Auto Standby" is set to "On", the AV receiver will
  • Onkyo HT-RC370 | Owner Manual - Page 59
    AV receiver's firmware. Do not shutdown the power of the AV receiver while updating. ■ Universal Port `via NET: Performs the firmware update via Internet. Check the network connection before updating. `via USB: Performs the firmware update from a USB device. These settings allow you to update Onkyo
  • Onkyo HT-RC370 | Owner Manual - Page 60
    in 2 dB steps. You can boost or cut high-frequency sounds output from the front speakers. You can adjust the bass and treble for the front speakers, except when the Direct, Pure Audio or THX listening mode is selected. Operating on the AV receiver 1 Press TONE repeatedly to select either "Bass" or
  • Onkyo HT-RC370 | Owner Manual - Page 61
    playing and the intention of the original sound designer, and with some material there will THX Cinema, THX Surround EX, and THX Select2 Cinema. Note • Settings for the Re-EQ function are kept in each listening mode. In THX listening mode however, the setting will return to "On" when the AV receiver
  • Onkyo HT-RC370 | Owner Manual - Page 62
    the AV receiver This setup allows 5.1-channel playback in your main room and 2-channel 2 R L Note • With this setup, the volume of Zone 2 is controlled by the AV receiver. • Powered Zone 2 cannot be connect Zone 2 speakers directly to the AV receiver, listening modes that require surround back
  • Onkyo HT-RC370 | Owner Manual - Page 63
    Controlling Zone 2 Components ■ Operating on the AV receiver Input selector buttons ZONE 2 OFF MASTER VOLUME Adjusting the Volume for Zone 2 ■ Operating on the remote controller 1 Press ZONE2. 2 Use VOL R/X to Zone 2 is set to share the same source, no sound will be output from Zone 2. En 63
  • Onkyo HT-RC370 | Owner Manual - Page 64
    site. For supported iPod/iPhone models, see the instruction manual of the Onkyo Dock. UP-A1 Dock With the UP-A1 Dock, you can easily play the music, photos, or movies stored on your Apple iPod/iPhone through the AV receiver and enjoy great sound. You can use the AV receiver's remote controller to
  • Onkyo HT-RC370 | Owner Manual - Page 65
    your Apple iPod/iPhone through the AV receiver and enjoy great sound, and watch iPod/iPhone slideshows Remote Control Codes" for details on entering a remote control code (➔ page 67). See the Dock's instruction manual for more information. ■ System Function System On When you turn on the AV receiver
  • Onkyo HT-RC370 | Owner Manual - Page 66
    operation of iPod/iPhone, please refer to the instruction manual of the RI Dock. *1 This button does not turn the Onkyo DS-A2 or DS-A2X RI Dock on iPod/iPhone is already off, it will remain off when the remote controller transmits the Off command. *2 TOP MENU works as the to the HDMI output. En 66
  • Onkyo HT-RC370 | Owner Manual - Page 67
    (➔ page 68) PORT Onkyo Universal Port Option (➔ page 65) Looking up for Remote Control Code You can look up for an appropriate remote control code from the on-screen setup menu. Note • This can only be carried out using the on-screen setup menu. 1 Press RECEIVER followed by SETUP. The main menu
  • Onkyo HT-RC370 | Owner Manual - Page 68
    models). The component must be able to receive remote control commands via Q and be connected to the AV receiver via HDMI. Use the following remote control codes: ` 32910/33101/33501/31612: Blu-ray Disc/DVD player with Q *1 The Q supported by the AV receiver is the CEC system control function of
  • Onkyo HT-RC370 | Owner Manual - Page 69
    *1 When you press SOURCE, the related component is turned on (or off). *2 The Q function is not supported. The Q supported by the AV receiver is the CEC system control function of the HDMI standard. *3  (Pause) functions as reverse playback. I *4 These buttons function as colored buttons or
  • Onkyo HT-RC370 | Owner Manual - Page 70
    AV receiver's remote controller can learn the commands of other remote controllers. By transmitting, for example, the Play command from your CD player's remote controller, the supplied remote Remote controller buttons such as Play, Stop, and Pause are preprogrammed with commands for controlling Onkyo
  • Onkyo HT-RC370 | Owner Manual - Page 71
    control actions. Example: To play a CD you typically need to perform the following actions: 1. Press RECEIVER to select the Receiver remote controller mode. 2. Press RECEIVER to turn on the AV receiver. 3. Press TV/CD to select the TV/CD input source. 4. Press  to start playback on the CD player
  • Onkyo HT-RC370 | Owner Manual - Page 72
    remote controller's MUTING to unmute the AV receiver. While a pair of headphones is connected to the 41 PHONES jack, no sound is output from the speakers. If there's no sound from a DVD player connected to - an HDMI IN, check the DVD player's output settings, and be sure to select a supported
  • Onkyo HT-RC370 | Owner Manual - Page 73
    , fast forward, or fast reverse function on your player. If you switch your player from DTS to PCM, because the AV receiver does not switch formats immediately, you may not hear any sound, in which case you should stop your player for about three seconds, and then resume playback. With some CD and
  • Onkyo HT-RC370 | Owner Manual - Page 74
    connected. If your TV is connected to the HDMI OUT, select 44 in the "HDMI Input" setup to watch composite video, S-Video and component video remote control 67 code. Make sure to set the same ID on both the AV 57 receiver and remote controller. ■ Can't control other components If it's an Onkyo
  • Onkyo HT-RC370 | Owner Manual - Page 75
    instructions. UP-A1 Dock for iPod/iPhone ■ There's no sound Make sure your iPod/iPhone is actually playing. - Make sure your iPod/iPhone is properly inserted in - the Dock. Make sure the UP-A1 Dock is connected to the - UNIVERSAL PORT jack on the AV receiver. Make sure the AV receiver
  • Onkyo HT-RC370 | Owner Manual - Page 76
    radio station, recheck the AV receiver's IP address on the "Network" screen. Check the "Network" settings. 59 USB Device Playback ■ Can't access the music files on a USB device Make sure the USB device is plugged in properly. - The AV receiver supports USB devices that support - the USB mass
  • Onkyo HT-RC370 | Owner Manual - Page 77
    HDMI OUT is unstable, try switching the DeepColor function off To turn off the DeepColor function, simultaneously press the CBL/SAT and ON/STANDBY buttons on the AV receiver at least five seconds, and then plug it back in. Onkyo is not responsible for damages (such as CD rental fees) due to
  • Onkyo HT-RC370 | Owner Manual - Page 78
    Firmware Update To update the firmware of the AV receiver, you can choose from the following two methods: update via network, or update via USB storage. Choose the one that best suits your environment. Before proceeding with the update, please read the corresponding explanations carefully. ■ Update
  • Onkyo HT-RC370 | Owner Manual - Page 79
    off and on the AV receiver. Do not use RECEIVER on the remote controller. Congratulations! You now have the latest firmware installed on your Onkyo AV receiver. Troubleshooting Case 1: If "No Update" is displayed on the front display of the AV receiver, it means that the firmware has already been
  • Onkyo HT-RC370 | Owner Manual - Page 80
    /STANDBY on the front panel, turn off the AV receiver and then remove the USB device. Do not use RECEIVER on the remote controller. Congratulations! You now have the latest firmware installed on your Onkyo AV receiver. Troubleshooting Case 1: If "No Update" is displayed on the front display of the
  • Onkyo HT-RC370 | Owner Manual - Page 81
    choose will depend on the formats supported by your components. Use the following sections as a guide. The on-screen menus appear only on a TV that is connected to the HDMI OUT. If your TV is connected to other video outputs, use the AV receiver's display when changing settings. Video Connection
  • Onkyo HT-RC370 | Owner Manual - Page 82
    -ray Disc/DVD player, etc. Analog Multichannel Optical Coaxial IN AV receiver *1 *1*3 *1 *1 *3 Analog OUT HDMI HDMI *1 *2 TV, projector, etc. *1 Depends on the "Audio TV Out" setting (➔ page 58). *2 This is possible when "Audio Return Channel" is set to "Auto" (➔ page 58), the TV/CD input
  • Onkyo HT-RC370 | Owner Manual - Page 83
    Resolution Chart The following tables show how video signals at different resolutions are output by the AV receiver. NTSC/PAL ✔: Output Output HDMI Input 4K*2 HDMI 1080p ✔ 1080i ✔ 720p ✔ 480p/576p ✔ 480i/576i ✔ Component 1080p ✔ 1080i ✔ 720p ✔ 480p/576p ✔ 480i/576i ✔ S-Video
  • Onkyo HT-RC370 | Owner Manual - Page 84
    Recorder Q, which stands for Remote Interactive over HDMI, is the name of the system control function found on Onkyo components. The AV receiver can be used with CEC (Consumer Electronics Control), which allows system control over HDMI and is part of the HDMI standard. CEC provides interoperability
  • Onkyo HT-RC370 | Owner Manual - Page 85
    AV receiver using an optical digital cable. Note • When the audio return channel (ARC) function is used with an ARC capable TV, this connection is not necessary (➔ page 58). 3. Connect the HDMI the input to which the AV receiver is connected. 5. Following the operating instructions of the TV, select
  • Onkyo HT-RC370 | Owner Manual - Page 86
    PC are not supported. • The HDMI audio signal (sampling rate, bit length, etc.) may be restricted by the connected source component. If the picture is poor or there's no sound from a component connected via HDMI, check its setup. Refer to the connected component's instruction manual for details. En
  • Onkyo HT-RC370 | Owner Manual - Page 87
    Consult your ISP if you have any problems with your Internet connection. • The AV receiver uses DHCP to configure its network settings automatically. If you want to configure these settings manually, see "Network" (➔ page 59). • The AV receiver does not support PPPoE settings, so if you have a PPPoE
  • Onkyo HT-RC370 | Owner Manual - Page 88
    to your USB MP3 player's instruction manual for details. • Protected WMA music files on an MP3 player cannot be played. • Onkyo accepts no responsibility whatsoever for the loss or damage to data stored on a USB device when that device is used with the AV receiver. We recommend that you back up
  • Onkyo HT-RC370 | Owner Manual - Page 89
    kHz, 32 kHz, 44.1 kHz, 48 kHz, 64 kHz, 88.2 kHz, and 96 kHz are supported. • Quantization bit: 8 bit, 16 bit, 24 bit * Only for playback via network. Note • With remote playback, the AV receiver does not support the following music file formats: FLAC and Ogg Vorbis. • In the case of server playback
  • Onkyo HT-RC370 | Owner Manual - Page 90
    RDS AM Tuning Frequency Range 522/530 kHz - 1611/1710 kHz Preset Channel 40 General Power Supply (North American) AC 120 V, 60 Hz (Chinese 6-7/8" × 14-15/16" Weight 12.5 kg (27.6 lbs.) ■ HDMI Input Output Video Resolution Audio Format Supported IN 1, IN 2, IN 3, IN 4, IN 5, IN 6, AUX
  • Onkyo HT-RC370 | Owner Manual - Page 91
    Outputs 7 Subwoofer Pre Outputs 2 Speaker Outputs Main (L, R, C, SL, SR, SBL, SBR) + Front Wide/ZONE2 (L, R) + Front High (L, R) Phones 1 (6.3 ø) ■ Others Setup Mic Universal Port RI USB Ethernet 1 1 1 1 (Front) 1 Specifications and features are subject to change without notice. En 91
  • Onkyo HT-RC370 | Owner Manual - Page 92
    onkyo.com/ 18 Park Way, Upper Saddle River, N.J. 07458, U.S.A. Tel: 800-229-1687, 201-785-2600 Fax: 201-785-2650 http://www.us.onkyo .com/ Liegnitzerstrasse 6, 82194 Groebenzell, GERMANY Tel: +49-8142-4401-0 Fax: +49-8142-4401-555 http://www.eu.onkyo 2428-9039 http://www.ch.onkyo.com/ 1301, 555
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
AV Receiver
HT-RC370
Instruction Manual
Thank you for purchasing an Onkyo AV Receiver.
Please read this manual thoroughly before making
connections and plugging in the unit.
Following the instructions in this manual will enable
you to obtain optimum performance and listening
enjoyment from your new AV Receiver.
Please retain this manual for future reference.
Contents
Introduction
...................................
2
Connections
.................................
12
Turning On & Basic Operations
......
22
Advanced Operations
.................
43
Controlling Other Components
...64
Appendix
......................................
72
E
n