Onkyo SKW-770 User Manual English - Page 7

Troubleshooting - manual

Page 7 highlights

Troubleshooting ■ The unit does not turn on The power plug is not fully inserted. ➔Insert the power plug fully into the power outlet. ■ No sound is output The OUTPUT LEVEL knob is set to the MIN level. ➔Set the OUTPUT LEVEL knob properly. Pin connector cable is not properly connected to the LINE INPUT jack. The speaker setting at the amplifier (or receiver) is incorrect. ➔Check the settings at the amplifier (or receiver). The input signal is so small that the unit entered Standby mode. ➔Slightly increase the output level at the amplifier (or receiver). If the Standby/On indicator lights up (both red and blue LEDs) several seconds or minutes after the sound output stopped, this means that the amp protection circuit has been activated. In this case, set the OUTPUT LEVEL knob to the center position, and disconnect the power cord from the AC outlet. Wait at least 10 seconds, and then reconnect the power cord. If that doesn't solve the issue, contact your Onkyo dealer. ■ Low sound output The sound source might not include a superbass range. ➔Play a sound source that includes a superbass range. ■ Hum noise Pin connector plug is not inserted completely. ➔Fully insert the pin connector plug. External leakage flux (induction noise by TV, etc.) occurs. ➔Relocate the SKW-770 away from the noise source and re-connect. Specifications Type Bass-Reflex Input sensitivity/impedance 550 mV/20 kΩ Frequency response 25 Hz to 150 Hz Rated output power (IEC) 120 watts minimum continuos power, 4 ohms, driven at 100 Hz with a maximum total harmonic distortion of 1 % Cabinet capacity 37 L Drivers unit 25 cm Cone woofer Power supply AC 220 - 240 V, 50/60 Hz Power consumption 137 W Dimensions (W × H × D) 275 mm × 507 mm × 411 mm (incl. grille and projection) Weight 11.6 kg Accessory Power cord (2 pcs.) Pin connector cable (1 pc.) Instruction manual (this manual) Floor pad (4 pcs.) Others Auto Standby function Non-magnetic shielding Specifications and appearance are subject to change without prior notice. En 7

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8

7
En
Troubleshooting
The unit does not turn on
No sound is output
Low sound output
Hum noise
Specifications
Specifications and appearance are subject to change
without prior notice.
The power plug is not fully inserted.
Insert the power plug fully into the power outlet.
The
OUTPUT LEVEL
knob is set to the
MIN
level.
Set the
OUTPUT LEVEL
knob properly.
Pin connector cable is not properly connected to the
LINE INPUT
jack.
The speaker setting at the amplifier (or receiver) is
incorrect.
Check the settings at the amplifier (or receiver).
The input signal is so small that the unit entered
Standby mode.
Slightly increase the output level at the amplifier
(or receiver).
If the
Standby/On
indicator lights up (both red and
blue LEDs) several seconds or minutes after the
sound output stopped, this means that the amp
protection circuit has been activated. In this case, set
the
OUTPUT LEVEL
knob to the center position,
and disconnect the power cord from the AC outlet.
Wait at least 10 seconds, and then reconnect the
power cord. If that doesn’t solve the issue, contact
your Onkyo dealer.
The sound source might not include a superbass
range.
Play a sound source that includes a superbass
range.
Pin connector plug is not inserted completely.
Fully insert the pin connector plug.
External leakage flux (induction noise by TV, etc.)
occurs.
Relocate the SKW-770 away from the noise
source and re-connect.
Type
Bass-Reflex
Input sensitivity/impedance
550 mV/20 k
Frequency response
25 Hz to 150 Hz
Rated output power (IEC)
120 watts minimum continuos power,
4 ohms, driven at 100 Hz with a maximum
total harmonic distortion of 1 %
Cabinet capacity
37 L
Drivers unit
25 cm Cone woofer
Power supply
AC 220 - 240 V, 50/60 Hz
Power consumption
137 W
Dimensions (W × H × D)
275 mm × 507 mm × 411 mm
(incl. grille and projection)
Weight
11.6 kg
Accessory
Power cord (2 pcs.)
Pin connector cable (1 pc.)
Instruction manual (this manual)
Floor pad (4 pcs.)
Others
Auto Standby function
Non-magnetic shielding